- •Recovered Paper and Recycled Fibers
- •Isbn: 3-527-30999-3
- •Introduction
- •Isbn: 3-527-30999-3
- •Isbn: 3-527-30999-3
- •2006, Isbn 3-527-30997-7
- •Volume 1
- •Isbn: 3-527-30999-3
- •4.1 Introduction 109
- •4.2.5.1 Introduction 185
- •4.3.1 Introduction 392
- •5.1 Introduction 511
- •6.1 Introduction 561
- •6.2.1 Introduction 563
- •6.4.1 Introduction 579
- •Volume 2
- •7.3.1 Introduction 628
- •7.4.1 Introduction 734
- •7.5.1 Introduction 777
- •7.6.1 Introduction 849
- •7.10.1 Introduction 887
- •8.1 Introduction 933
- •1 Introduction 1071
- •5 Processing of Mechanical Pulp and Reject Handling: Screening and
- •1 Introduction 1149
- •Isbn: 3-527-30999-3
- •Isbn: 3-527-30999-3
- •Isbn: 3-527-30999-3
- •Isbn: 3-527-30999-3
- •Introduction
- •Introduction
- •Isbn: 3-527-30999-3
- •1 Introduction
- •1 Introduction
- •1 Introduction
- •1 Introduction
- •1 Introduction
- •1 Introduction
- •150.000 Annual Fiber Flow[kt]
- •1 Introduction
- •1 Introduction
- •Introduction
- •Isbn: 3-527-30999-3
- •Void volume
- •Void volume fraction
- •Xylan and Fiber Morphology
- •Initial bulk residual
- •4.2.5.1 Introduction
- •In (Ai) Model concept Reference
- •Initial value
- •Validation and Application of the Kinetic Model
- •Inititial
- •Viscosity
- •Influence on Bleachability
- •Impregnation
- •Impregnation
- •Impregnation
- •Impregnation
- •Impregnation
- •Impregnation
- •Impregnation
- •Impregnation
- •Impregnation
- •Impregnation
- •Introduction
- •International
- •Impregnation
- •Influence of Substituents on the Rate of Hydrolysis
- •140 116 Total so2
- •Xylonic
- •Viscosity Brightness
- •Xyl Man Glu Ara Furf hoAc XyLa
- •Initial NaOh charge [% of total charge]:
- •Introduction
- •Isbn: 3-527-30999-3
- •Introduction
- •Isbn: 3-527-30999-3
- •Introduction
- •Introduction
- •Isbn: 3-527-30999-3
- •Introduction
- •Xylosec
- •Xylan residues
- •Viscosity
- •Introduction
- •Viscosity
- •Viscosity
- •Introduction
- •Initiator Promoter Inhibitor
- •Viscosity
- •Viscosity
- •Viscosity
- •Introduction
- •Viscosity
- •Introduction
- •Intra-Stage Circulation and Circulation between Stages
- •Implications of Liquor Circulation
- •Vid Chalmers Tekniska
- •Introduction
- •It is a well-known fact that the mechanical properties of the viscose fibers
- •Increase in the low molecular-weight fraction [2]. The short-chain molecules represent
- •Isbn: 3-527-30999-3
- •In the cooking process or, alternatively, white liquor can be used for the cold
- •Is defined as the precipitate formed upon acidification of an aqueous alkaline solution
- •934 8 Pulp Purification
- •8.2 Reactions between Pulp Constituents and Aqueous Sodium Hydroxide Solution 935
- •Is essentially governed by chemical degradation reactions involving endwise depolymerization
- •80 °C [12]. Caustic treatment: 5%consistency ,
- •30 Min reaction time, NaOh concentrations:
- •8.2 Reactions between Pulp Constituents and Aqueous Sodium Hydroxide Solution
- •80 °C is mainly governed by chemical degradation reactions (e.G. Peeling reaction).
- •Investigated using solid-state cp-mas 13c-nmr spectroscopy (Fig. 8.4).
- •Indicates cleavage of the intramolecular hydrogen bond between o-3-h and o-5′,
- •8 Pulp Purification
- •Interaction between alkali and cellulose, a separate retention tower is not really
- •In the following section.
- •3% In the untreated pulp must be ensured in order to avoid a change in the supramolecular
- •8.3 Cold Caustic Extraction
- •Xylan content [%]
- •8 Pulp Purification
- •Is calculated as effective alkali (ea). Assuming total ea losses (including ea consumption
- •Xylan content [%]
- •8.3 Cold Caustic Extraction
- •120 °C (occasionally 140 °c). As mentioned previously, hce is carried out solely
- •Involved in alkaline cooks (kraft, soda), at less severe conditions and thus avoiding
- •8.4Hot Caustic Extraction 953
- •954 8 Pulp Purification
- •120 Kg NaOh odt–1, 90–240 min, 8.4 bar (abs)
- •8.4Hot Caustic Extraction 955
- •956 8 Pulp Purification
- •Into the purification reaction, either in the same (eo) or in a separate stage
- •960 8 Pulp Purification
- •8.4.1.5 Composition of Hot Caustic Extract
- •8.4Hot Caustic Extraction 961
- •Isbn: 3-527-30999-3
- •Xyloisosaccharinic acid
- •Inorganicsa
- •Inorganic compounds
- •Value (nhv), which better reflects the actual energy release, accounts for the fact
- •968 9 Recovery
- •It should be noted that the recycling of bleach (e.G., oxygen delignification) and
- •9.1 Characterization of Black Liquors 969
- •9.1.2.1 Viscosity
- •9.1.2.3 Surface Tension
- •9.1.2.5 Heat Capacity [8,11]
- •9.2 Chemical Recovery Processes
- •Is described by the empirical equation:
- •9 Recovery
- •Vent gases from all areas of the pulp mill. From an environmental perspective,
- •9.2.2.1 Introduction
- •In the sump at the bottom of the evaporator. The generated vapor escapes
- •Incineration, whereas sulphite ncg can be re-used for cooking acid preparation.
- •9 Recovery
- •Values related to high dry solids concentrations. The heat transfer rate is pro-
- •9.2 Chemical Recovery Processes
- •9.2.2.3 Multiple-Effect Evaporation
- •7% Over effects 4 and 5, but more than 30% over effect 1 alone.
- •9.2 Chemical Recovery Processes
- •Increasing the dry solids concentration brings a number of considerable advantages
- •9.2.2.4 Vapor Recompression
- •Is driven by electrical power. In general, vapor coming from the liquor
- •Vapor of more elevated temperature, thus considerably improving their performance.
- •9 Recovery
- •Is typically around 6 °c. The resulting driving temperature difference
- •Is low, and hence vapor recompression plants require comparatively large heating
- •Vapor recompression systems need steam from another source for start-up.
- •9 Recovery
- •Its temperature is continuously falling to about 180 °c. After the superheaters,
- •In the furnace walls, and only 10–20% in the boiler bank. As water turns into
- •9.2.3.1.2 Material Balance
- •Is required before the boiler ash is mixed. In addition, any chemical make-up
- •In this simplified model, all the potassium from the black liquor (18 kg t–1
- •Values for the chemicals in Eq. (11) can be inserted on a molar basis, equivalent
- •9.2 Chemical Recovery Processes
- •Input/output
- •9 Recovery
- •9.2.3.1.3 Energy Balance
- •In the black liquor, from water formed out of hydrogen in organic material, and
- •9.2 Chemical Recovery Processes
- •9.2.3.2 Causticizing and Lime Reburning
- •9.2.3.2.1 Overview
- •9.2.3.2.2 Chemistry
- •986 9 Recovery
- •Insoluble metal salts are kept low. Several types of filters with and without lime
- •Is, however, not considered a loss because some lime mud must be
- •988 9 Recovery
- •In slakers and causticizers needs special attention in order to avoid particle disintegration,
- •9.2 Chemical Recovery Processes 989
- •Ing disks into the center shaft, and flows to the filtrate separator. There, the white
- •9.2.3.2.4 Lime Cycle Processes and Equipment
- •It is either dried with flue gas in a separate, pneumatic lime mud dryer or is fed
- •990 9 Recovery
- •Its temperature falls gradually. Only about one-half of the chemical energy in the
- •9.2.3.3.2 Black Liquor Gasification
- •Inorganics leave the reactor as solids, and into high-temperature techniques,
- •In the bed. Green liquor is produced from surplus bed solids. The product gas
- •992 9 Recovery
- •Incremental capacity for handling black liquor solids. The encountered difficulties
- •10% Of today’s largest recovery boilers. When the process and material issues are
- •9.2 Chemical Recovery Processes 993
- •9.2.3.3.3 In-Situ Causticization
- •Is still in the conceptual phase, and builds on the formation of sodium titanates
- •9.2.3.3.4 Vision Bio-Refinery
- •Into primary and secondary recovery steps. This definition relates to the recovery
- •994 9 Recovery
- •Is largely different between sulfite cooking bases. While magnesium and
- •Introduction
- •In alkaline pulping the operation of the lime kiln represents an emission source.
- •Isbn: 3-527-30999-3
- •Is by the sophisticated management of these sources. This comprises their collection,
- •Ions, potassium, or transition metals) in the process requires the introduction
- •Industry”. Similarly guidelines for a potential kraft pulp mill in Tasmania [3]
- •Initially, the bleaching of chemical pulp was limited to treatment with hypochlorite
- •In a hollander, and effluent from the bleach plant was discharged without
- •In a heh treatment and permitted higher brightness at about 80% iso (using
- •Increasing pulp production resulted in increasing effluent volumes and loads.
- •10.2 A Glimpse of the Historical Development 999
- •It became obvious that the bleaching process was extremely difficult to operate in
- •In a c stage was detected as aox in the effluent (50 kg Cl2 t–1 pulp generated
- •1% Of the active chlorine is converted into halogenated compounds (50 kg active
- •In chlorination effluent [12] led to the relatively rapid development of alternative
- •1000 10 Environmental Aspects of Pulp Production
- •10.2 A Glimpse of the Historical Development
- •In 1990, only about 5% of the world’s bleached pulp was produced using ecf
- •64 Million tons of pulp [14]. The level of pulp still bleached with chlorine
- •10 000 Tons. These are typically old-fashioned, non-wood mills pending an
- •In developed countries, kraft pulp mills began to use biodegradation plants for
- •10 Environmental Aspects of Pulp Production
- •Indeed, all processes are undergoing continual development and further improvement.
- •Vary slightly different depending upon the type of combustion unit and the fuel
- •10.3Emissions to the Atmosphere
- •Volatile organic
- •In 2004 for a potential pulp mill in Tasmania using “accepted
- •10 Environmental Aspects of Pulp Production
- •Is woodyard effluent (rain water), which must be collected and treated biologically
- •10.4 Emissions to the Aquatic Environment
- •Is converted into carbon dioxide, while the other half is converted into biomass
- •Into alcohols and aldehydes; (c) conversion of these intermediates into acetic acid and
- •10 Environmental Aspects of Pulp Production
- •In North America, effluent color is a parameter which must be monitored.
- •It is not contaminated with other trace elements such as mercury, lead, or cadmium.
- •10.6 Outlook
- •Increase pollution by causing a higher demand for a chemical to achieve identical
- •In addition negatively affect fiber strength, which in turn triggers a higher
- •Introduction
- •2002, Paper-grade pulp accounts for almost 98% of the total wood pulp production
- •Important pulping method until the 1930s) continuously loses ground and finds
- •Importance in newsprint has been declining in recent years with the increasing
- •Isbn: 3-527-30999-3
- •Virtually all paper and paperboard grades in order to improve strength properties.
- •In fact, the word kraft is the Swedish and German word for strength. Unbleached
- •Importance is in the printing and writing grades. In these grades, softwood
- •In this chapter, the main emphasis is placed on a comprehensive discussion of
- •1010 11 Pulp Properties and Applications
- •Is particularly sensitive to alkaline cleavage. The decrease in uronic acid content
- •Xylan in the surface layers of kraft pulps as compared to sulfite pulps has been
- •80% Cellulose content the fiber strength greatly diminishes [14]. This may be due
- •Viscoelastic and capable of absorbing more energy under mechanical stress. The
- •11.2 Paper-Grade Pulp 1011
- •Various pulping treatments using black spruce with low fibril
- •In the viscoelastic regions. Fibers of high modulus and elasticity tend to peel their
- •1012 11 Pulp Properties and Applications
- •11.2 Paper-Grade Pulp
- •Viscosity mL g–1 793 635 833 802 1020 868 1123
- •Xylose % od pulp 7.3 6.9 18.4 25.5 4.1 2.7 12.2
- •11 Pulp Properties and Applications
- •Inorganic Compounds
- •11.2 Paper-Grade Pulp
- •Insight into many aspects of pulp origin and properties, including the type of
- •Indicate oxidative damage of carbohydrates).
- •In general, the r-values of paper pulps are typically at higher levels as predicted
- •Is true for sulfite pulps. Even though the r-values of sulfite pulps are generally
- •Is rather unstable in acid sulfite pulping, and this results in a low (hemicellulose)
- •11 Pulp Properties and Applications
- •Ing process, for example the kraft process, the cellulose:hemicellulose ratio is
- •Increases by up to 100%. In contrast to fiber strength, the sheet strength is highly
- •Identified as the major influencing parameter of sheet strength properties. It has
- •In contrast to dissolving pulp specification, the standard characterization of
- •Is observed for beech kraft pulp, which seems to correlate with the enhanced
- •11.2 Paper-Grade Pulp
- •11 Pulp Properties and Applications
- •Is significantly higher for the sulfite as compared to the kraft pulps, and indicates
- •11.2 Paper-Grade Pulp
- •Xylan [24].
- •11 Pulp Properties and Applications
- •11.2 Paper-Grade Pulp
- •11 Pulp Properties and Applications
- •Introduction
- •Various cellulose-derived products such as regenerated fibers or films (e.G.,
- •Viscose, Lyocell), cellulose esters (acetates, propionates, butyrates, nitrates) and
- •In pulping and bleaching operations are required in order to obtain a highquality
- •Important pioneer of cellulose chemistry and technology, by the statement that
- •11.3 Dissolving Grade Pulp
- •Involves the extensive characterization of the cellulose structure at three different
- •Is an important characteristic of dissolving pulps. Finally, the qualitative and
- •Inorganic compounds
- •11 Pulp Properties and Applications
- •11.3.2.1 Pulp Origin, Pulp Consumers
- •Include the recently evaluated Formacell procedure [7], as well as the prehydrolysis-
- •11.3 Dissolving Grade Pulp
- •Viscose
- •11 Pulp Properties and Applications
- •11.3.2.2 Chemical Properties
- •11.3.2.2.1 Chemical Composition
- •In the polymer. The available purification processes – particularly the hot and cold
- •11.3 Dissolving Grade Pulp
- •In the steeping lye inhibits cellulose degradation during ageing due to the
- •Is governed by a low content of noncellulosic impurities, particularly pentosans,
- •Increase in the xylan content in the respective viscose fibers clearly support the
- •11.3 Dissolving Grade Pulp
- •Instability. Diacetate color is measured by determining the yellowness coefficient
- •Xylan content [%]
- •11 Pulp Properties and Applications
- •Xylan content [%]
- •11.3 Dissolving Grade Pulp
- •11.3 Dissolving Grade Pulp
- •Is, however, not the only factor determining the optical properties of cellulosic
- •In the case of alkaline derivatization procedures (e.G., viscose, ethers). In industrial
- •11.3 Dissolving Grade Pulp
- •Viscose
- •Viscose
- •In order to bring out the effect of mwd on the strength properties of viscose
- •Imitating the regular production of rayon fibers. To obtain a representative view
- •11 Pulp Properties and Applications
- •Viscose Ether (hv) Viscose Acetate Acetate
- •Xylan % 3.6 3.1 1.5 0.9 0.2
- •1.3 Dtex regular viscose fibers in the conditioned
- •11.3 Dissolving Grade Pulp
- •Is more pronounced for sulfite than for phk pulps. Surprisingly, a clear correlation
- •Viscose fibers in the conditioned state related to the carbonyl
- •1038 11 Pulp Properties and Applications
- •In a comprehensive study, the effect of placing ozonation before (z-p) and after
- •Increased from 22.9 to 38.4 lmol g–1 in the case of a pz-sequence, whereas
- •22.3 To 24.2 lmol g–1. The courses of viscosity and carboxyl group contents were
- •Viscosity measurement additionally induces depolymerization due to strong
- •11 Pulp Properties and Applications
- •Increasing ozone charges. For more detailed
- •11.3 Dissolving Grade Pulp
- •Is more selective when ozonation represents the final stage according to an
- •11.3.2.3 Supramolecular Structure
- •1042 11 Pulp Properties and Applications
- •Is further altered by subsequent bleaching and purification processes. This
- •Involved in intra- and intermolecular hydrogen bonds. The softened state favors
- •11.3 Dissolving Grade Pulp
- •Interestingly, the resistance to mercerization, which refers to the concentration of
- •11 Pulp Properties and Applications
- •Illustrate that the difference in lye concentration between the two types of dissolving
- •Intensity (see Fig. 11.18: hw-phk high p-factor) clearly changes the supramolecular
- •11.3 Dissolving Grade Pulp
- •Viscose filterability, thus indicating an improved reactivity.
- •11 Pulp Properties and Applications
- •Impairs the accessibility of the acetylation agent. When subjecting a low-grade dissolving
- •Identification of the cell wall layers is possible by the preferred orientation of
- •Viscose pulp (low p-factor) (Fig. 11.21b, top). Apparently, the type of pulp – as well
- •11 Pulp Properties and Applications
- •150 °C for 2 h, more than 70% of a xylan, which was added to the cooking liquor
- •20% In the case of alkali concentrations up to 50 g l–1 [67]. Xylan redeposition has
- •11.3 Dissolving Grade Pulp
- •Xylan added linters cooked without xylan linters cooked with xylan
- •Viscosity
- •In the surface layer than in the inner fiber wall. This is in agreement with
- •11 Pulp Properties and Applications
- •Xylan content in peelings [wt%]
- •Xylan content located in the outermost layers of the beech phk fibers suggests
- •11.3.2.5 Fiber Morphology
- •11 Pulp Properties and Applications
- •50 And 90%. Moreover, bleachability of the screened pulps from which the wood
- •11.3.2.6 Pore Structure, Accessibility
- •11.3 Dissolving Grade Pulp
- •Volume (Vp), wrv and specific pore surface (Op) were seen between acid sulfite
- •11 Pulp Properties and Applications
- •Irreversible loss of fiber swelling occurs; indeed, Maloney and Paulapuro reported
- •In microcrystalline areas as the main reason for hornification [85]. The effect of
- •105 °C, thermal degradation proceeds in parallel with hornification, as shown in
- •Increased, particularly at temperatures above 105 °c. The increase in carbonyl
- •In pore volume is clearly illustrated in Fig. 11.28.
- •11.3 Dissolving Grade Pulp
- •Viscosity
- •11 Pulp Properties and Applications
- •Increase in the yellowness coefficient, haze, and the amount of undissolved particles.
- •11.3.2.7 Degradation of Dissolving Pulps
- •In mwd. A comprehensive description of all relevant cellulose degradation processes
- •Is reviewed in Ref. [4]. The different modes of cellulose degradation comprise
- •11.3 Dissolving Grade Pulp
- •50 °C, is illustrated graphically in Fig. 11.29.
- •11 Pulp Properties and Applications
- •In the crystalline regions.
- •11.3 Dissolving Grade Pulp
- •Important dissolving pulps, derived from hardwood, softwood and cotton linters
- •11.3 Dissolving Grade Pulp 1061
- •Xylan rel% ax/ec-pad 2.5 3.5 1.3 1.0 3.2 0.4
- •Viscosity mL g–1 scan-cm 15:99 500 450 820 730 1500 2000
- •1062 11 Pulp Properties and Applications
- •Isbn: 3-527-30999-3
- •Introduction
- •Isbn: 3-527-30999-3
- •1072 1 Introduction
- •Isbn: 3-527-30999-3
- •Inventor of stone groundwood. Right: the second version
- •1074 2 A Short History of Mechanical Pulping
- •In refining, the thinnings (diameter 7–10cm) can also be processed.
- •In mechanical pulping as it causes foam; the situation is especially
- •In mechanical pulping, those fibers that are responsible for strength properties
- •Isbn: 3-527-30999-3
- •In mechanical pulping, the wood should have a high moisture content, and the
- •In the paper and reduced paper quality. The higher the quality of the paper, the
- •1076 3 Raw Materials for Mechanical Pulp
- •1, Transversal resistance; 2, Longitudinal resistance; 3, Tanning limit.
- •3.2 Processing of Wood 1077
- •In the industrial situation in order to avoid problems of pollution and also
- •1078 3 Raw Materials for Mechanical Pulp
- •2, Grinder pit; 3, weir; 4, shower water pipe;
- •5, Wood magazine; 6, finger plate; 7, pulp stone
- •Isbn: 3-527-30999-3
- •4.1.2.1 Softening of the Fibers
- •1080 4 Mechanical Pulping Processes
- •235 °C, whereas according to Styan and Bramshall [4] the softening temperatures
- •Isolated lignin, the softening takes place at 80–90 °c, and additional water
- •4.1 Grinding Processes 1081
- •1082 4 Mechanical Pulping Processes
- •1, Cool wood; 2, strongly heated wood layer; 3, actual grinding
- •4.1.2.2 Defibration (Deliberation) of Single Fibers from the Fiber Compound
- •4 Mechanical Pulping Processes
- •Influence of Parameters on the Properties of Groundwood
- •In the mechanical defibration of wood by grinding, several process parameters
- •Improved by increasing both parameters – grinding pressure and pulp stone
- •In practice, the temperature of the pit pulp is used to control the grinding process,
- •In Fig. 4.8, while the grit material of the pulp stone estimates the microstructure
- •4 Mechanical Pulping Processes
- •4.1 Grinding Processes
- •Is of major importance for process control in grinding.
- •4 Mechanical Pulping Processes
- •4.1.4.2 Chain Grinders
- •Is fed continuously, as shown in Fig. 4.17.
- •Initial thickness of the
- •75 Mm thickness, is much thinner than that of a concrete pulp stone, much
- •4 Mechanical Pulping Processes
- •Include:
- •Increases; from the vapor–pressure relationship, the boiling temperature is seen
- •4 Mechanical Pulping Processes
- •In the pgw proves, and to prevent the colder seal waters from bleeding onto the
- •4.1 Grinding Processes
- •In pressure grinding, the grinder shower water temperature and flow are
- •70 °C, a hot loop is no longer used, and the grinding process is
- •4 Mechanical Pulping Processes
- •Very briefly at a high temperature and then refined at high
- •4.2 Refiner Processes
- •4 Mechanical Pulping Processes
- •Intensity caused by plate design and rotational speed.
- •4.2 Refiner Processes
- •1. Reduction of the chips sizes to units of matches.
- •2. Reduction of those “matches” to fibers.
- •3. Fibrillation of the deliberated fibers and fiber bundles.
- •1970S as result of the improved tmp technology. Because the key subprocess in
- •4 Mechanical Pulping Processes
- •Impregnation Preheating Cooking Yield
- •30%. Because of their anatomic structure, hardwoods are able to absorb more
- •Is at least 2 mWh t–1 o.D. Pulp for strongly fibrillated tmp and ctmp pulps from
- •4 Mechanical Pulping Processes
- •4.2 Refiner Processes
- •1500 R.P.M. (50 Hz) or 1800 r.P.M. (60 Hz); designed pressure 1.4 mPa
- •1500 R.P.M. (50 Hz) or 1800 r.P.M. (60 Hz); designed pressure 1.4 mPa;
- •4.2 Refiner Processes
- •4 Mechanical Pulping Processes
- •In hardwoods makes them more favorable than softwoods for this purpose. A
- •4.2 Refiner Processes
- •Isbn: 3-527-30999-3
- •1114 5 Processing of Mechanical Pulp and Reject Handling: Screening and Cleaning
- •5.2Machines and Aggregates for Screening and Cleaning 1115
- •In refiner mechanical pulping, there is virtually no such coarse material in the
- •1116 5 Processing of Mechanical Pulp and Reject Handling: Screening and Cleaning
- •5.2Machines and Aggregates for Screening and Cleaning
- •5 Processing of Mechanical Pulp and Reject Handling: Screening and Cleaning
- •5 Processing of Mechanical Pulp and Reject Handling: Screening and Cleaning
- •5.3 Reject Treatment and Heat Recovery
- •55% Iso and 65% iso. The intensity of the bark removal, the wood species,
- •Isbn: 3-527-30999-3
- •1124 6 Bleaching of Mechanical Pulp
- •Initially, the zinc hydroxide is filtered off and reprocessed to zinc dust. Then,
- •2000 Kg of technical-grade product is common. Typically, a small amount of a chelant
- •6.1 Bleaching with Dithionite 1125
- •Vary, but are normally ca. 10 kg t–1 or 1% on fiber. As the number of available
- •1126 6 Bleaching of Mechanical Pulp
- •6.2 Bleaching with Hydrogen Peroxide
- •70 °C, 2 h, amount of NaOh adjusted.
- •6.2 Bleaching with Hydrogen Peroxide
- •Is shown in Fig. 6.5, where silicate addition leads to a higher brightness and a
- •Volume (bulk). For most paper-grade applications, fiber volume should be low in
- •Valid and stiff fibers with a high volume are an advantage; however, this requires
- •1130 6 Bleaching of Mechanical Pulp
- •6.2 Bleaching with Hydrogen Peroxide
- •Very high brightness can be achieved with two-stage peroxide bleaching, although
- •In a first step. This excess must be activated with an addition of caustic soda. The
- •Volume of liquid to be recycled depends on the dilution and dewatering conditions
- •6 Bleaching of Mechanical Pulp
- •6 Bleaching of Mechanical Pulp
- •Is an essential requirement for bleaching effectiveness. Modern twin-wire presses
- •Is discharged to the effluent treatment plant. After the main bleaching stage, the
- •6.3 Technology of Mechanical Pulp Bleaching
- •1136 6 Bleaching of Mechanical Pulp
- •Isbn: 3-527-30999-3
- •7.3 Shows the fractional composition according to the McNett principle versus
- •1138 7 Latency and Properties of Mechanical Pulp
- •7.2 Properties of Mechanical Pulp 1139
- •Isbn: 3-527-30999-3
- •In 1950, about 50% of the global paper production was produced. This proportion
- •4.0% Worldwide; 4.2% for the cepi countries; and 4.8% for Germany.
- •1150 1 Introduction
- •1 Introduction
- •1 Introduction
- •Virgin fibers
- •74.4 % Mixed grades
- •Indonesia
- •Virgin fibers
- •Inhomogeneous sample Homogeneous sample
- •Variance of sampling Variance of measurement
- •1.Quartile
- •3.Quartile
- •Insoluble
- •Insoluble
- •Insoluble
- •Integral
- •In Newtonion liquid
- •Velocity
- •Increasing dp
- •2Α filter
- •0 Reaction time
- •Increasing interaction of probe and cellulose
- •Increasing hydrodynamic size
- •Vessel cell of beech
- •Initial elastic range
- •Internal flow
- •Intact structure
- •Viscosity 457
- •Isbn: 3-527-30999-3
- •1292 Index
- •Visbatch® pulp 354
- •Index 1293
- •1294 Index
- •Impregnation 153
- •Viscosity–extinction 433
- •Index 1295
- •1296 Index
- •Index 1297
- •Inhibitor 789
- •1298 Index
- •Index 1299
- •Impregnation liquor 290–293
- •1300 Index
- •Industries
- •Index 1301
- •1302 Index
- •Index 1303
- •Xylose 463
- •1304 Index
- •Index 1305
- •1306 Index
- •Index 1307
- •1308 Index
- •In conventional kraft cooking 232
- •Visbatch® pulp 358
- •Index 1309
- •In prehydrolysis-kraft process 351
- •Visbatch® cook 349–350
- •1310 Index
- •Index 1311
- •1312 Index
- •Viscosity 456
- •Index 1313
- •Viscosity 459
- •Interactions 327
- •1314 Index
- •Index 1315
- •Viscosity 459
- •1316 Index
- •Index 1317
- •Xylose 461
- •Index 1319
- •Visbatch® pulp 355
- •Impregnation 151–158
- •1320 Index
- •Index 1321
- •1322 Index
- •Xylan water prehydrolysis 333
- •Index 1323
- •1324 Index
- •Viscosity 459
- •Index 1325
- •Xylose 940
- •1326 Index
- •Index 1327
- •In selected kinetics model 228–229
- •4OMeGlcA 940
- •1328 Index
- •Index 1329
- •Intermediate molecule 164–165
- •1330 Index
- •Viscosity 456
- •Index 1331
- •1332 Index
- •Impregnation liquor 290–293
- •Index 1333
- •1334 Index
- •Index 1335
- •1336 Index
- •Impregnation 153
- •Index 1337
- •1338 Index
- •Viscose process 7
- •Index 1339
- •Volumetric reject ratio 590
- •1340 Index
- •Index 1341
- •1342 Index
- •Index 1343
- •1344 Index
- •Index 1345
- •Initiator 788
- •Xylose 463
- •1346 Index
- •Index 1347
- •Vessel 385
- •Index 1349
- •1350 Index
- •Xylan 834
- •1352 Index
Vid Chalmers Tekniska
Hogskola, 1998.
35 Lapierre, L., Bouchard, J., Berry, R.M.,
van Lierop, V., Chelation prior to hydrogen
peroxide bleaching of kraft pulps:
an overview. J. Pulp Paper Sci., 1995;
21(8): 268–273.
36 Bouchard, J., H.M. Nugent, R.M. Berry,
A comparison between acid treatment
and chelation prior to hydrogen peroxide
bleaching of kraft pulps. J. Pulp
Paper Sci., 1995; 21(6): 203–208.
37 Phinney, S., Less bleach – Brighter
paper. Chemical Innovation, 2001: 3–5.
38 Sjogren, B., J. Hook, Extended oxygen
delignification – The effect of pretreatments
and process conditions. 2000
International Pulp Bleaching Conference:
Oral Presentations, 2000: 89–96.
39 Gratzl, J.S., The chemical principles of
pulp bleaching with oxygen, hydrogen
peroxide and ozone – a short review. Die
chemischen Grundlagen der Zellstoffbleiche
mit Sauerstoff,Wasserstoffperoxid
und Ozon – ein kurzer Uberblick.
Papier, 1992; 46(10A): V1–V8.
40 Guay, D.F., Cole, B.J.W., Fort, R.C.,
Hausman, M.C.,Genco, J.M., Elder, T. J.,
Overly, K.R., Mechanisms of oxidative
degradation of carbohydrates during
oxygen delignification. II. Reaction of
photochemically generated hydroxyl
radicals with methyl beta-cellobioside.
J. Wood Chem. Technol., 2001; 21(1):
67–79.
41 Guay, D.F., Cole, B.J.W., Fort, Jr. R.C.,
Genco, J.M., Hausman, M.C., b-D-glucopyranoside
with photochemically generated
hydroxyl radicals. J. Wood Chem.
Technol., 2000: 20: 375–394.
42 Guay, D.F., Cole, B.J.W., Fort, Jr. R.C.,
Hausman, M.C., Genco, J.M., Elder, T.J.,
Mechanisms of oxidative degradation of
carbohydrates during oxygen delignification.
Part III: Reaction of photochemically
generated hydroxyl radicals with
1,5-anhydrocellobitol and cellulose. J.
Pulp Paper Sci., 2002; 28(7): 217–221.
43 Zeronian, S.H., M.K. Inglesby, Bleaching
of cellulose by hydrogen peroxide.
Cellulose, 1995; 2(4): 265–272.
References 929
44 Lewin, M., Oxidation and aging of cellulose.
Macromolecular Symposia, 1997;
118: 715–724.
45 Chirat, C., Mateo, C., Furstoss, H.,
Jeunet, A., Lachenal, D., Formation of
chromophores from carbohydrates during
pulping and their impact on bleaching.
Pulp Paper Canada, 2002; 103(2):
28–30.
46 Mielisch, H.-J., O. Kordsachia, and
R. Patt, Katalysierte Wasserstoffperoxidbleiche.
Das Papier, 1996; 50: V16–V23.
47 Suess, H.U., W. Eul, O. Hemling, Semibleaching
of Kraft pulp using oxygen
and hydrogen peroxide. Das Papier,
1989; 43(7): 318–323.
48 Suess, H.U., J.D. Kronis. Impact of carbonate
ions on hydrogen peroxide in
sodium carbonate solutions. In International
Pulp Bleaching Conference, Portland,
OR, 2002.
49 Lee, H.H.B., A.-H. Park, C. Oloman,
Stability of hydrogen peroxide in
sodium carbonate solutions. Tappi J.,
2000; 83(8): 94.
50 Stromberg, C.B., R. Szopinski. Pressurized
hydrogen peroxide bleaching for
improved TCF bleaching. In International
Pulp Bleaching Conference, Vancouver,
BC, TAPPI Press, 1994.
51 Dillner, B., Tibbling. Optimum use of
peroxide and ozone in TCF bleaching.
In International Pulp Bleaching Conference.
Vancouver, BC: TAPPI Press,
1994.
52 Suess, H.U., C.L. Filho. ECF Bleaching:
Balancing hydrogen peroxide bleaching
effects and pulp yield. In ABTC Annual
Meeting, 1997.
53 Suess, H.U., N. Nimmerfroh,
H.D. Kronis, The naked truth on hot
peroxide bleaching. Pulp Paper Canada,
1998; 99(4): T122–T125.
54 Colodette, J.L., S. Rothenburger,
C.W. Dence, Factors affecting hydrogen
peroxide stability in the brightening of
mechanical and chemimechanical
pulps. Part III: Hydrogen peroxide stability
in the presence of magnesium
and combinations of stabilizers. J. Pulp
Paper Sci., 1989; 15(2): J45.
55 Suess, H.U., B. Hopf, K. Schmidt, Optimising
peroxide bleaching of deinked
pulps in the disperser. Wochenblatt fur
Papierfabrikation, 2002; 130(11/12):
738–745.
56 Sjodin, L., S. Noren. Extended delignification
with oxygen and hydrogen peroxide
in ECF and TCF sequences. In Tappi
Pulping Conference, 1994.
57 Ragnar, M., Alkaline extraction and a
control strategy for the chlorine dioxide
charge to the final stage in DED bleaching.
Nordic Pulp Paper Res. J., 2003;
18(2): 162–167.
58 Milanez, A., J.L. Colodette. Optimum
conditions for bleaching eucalyptus
kraft pulp with a three stage sequence.
In International Pulp Bleaching Conference,
Stockholm, 2005.
59 Strunk, W.G., Kraft bleach plants
increase use of hydrogen peroxide as
benefits mount. Pulp Paper, 1990; 1 0:
112–116.
60 Hook, J., L. Mueller, S. Wallin, Vateperoxid
iakalistegen hojer kvaiteten. Nordisk
Cellulosa, 1985; 2: 47–50.
61 Andersson, L., et al. The use of hydrogen
peroxide bleaching for bleaching of
chemical pulp. In Tappi Pulping Conference,
1985.
62 Loufti, H., The use of hydrogen peroxide
in bleaching of North-Eastern softwood
pulp. In CPPA Annual Meeting,
1981.
63 PAPTAC, Standard Testing Methods,
Montreal, Sep. 2003.
64 Gullichsen, J., The influence of temperature
and humidity in the color reversion
of pulp. Pap. Puu, 1965; 47: 215.
65 Hausalo, T., L. Soderhjelm, Chemical
analysis of pulps. In Pulp and Paper Testing,
J.E. Levlin, L. Soderhjelm, Eds.
Fapet Oy: Helsinki, 1999: 128–129.
66 Rydholm, S.A., Pulping Processes. Malabar,
Florida: Robert E. Krieger Publishing
Co., Inc., 1965: 851–854.
67 Gellerstedt, G., O. Dahlman. Recent
hypothesis for brightness reversion of
hardwood pulps. In International Colloquium
on Eucalyptus Kraft pulp. Universidade
Federal de Vicosa, MG, Brazil,
2003.
68 Tenkanen, M., et al., Heat-induced
brightness reversion of ECF-light
bleached pine kraft pulp. In 7th European
Workshop on Lignocellulosics
and Pulp. Turku, 2002.
930 7Pulp Bleaching
69 Suess, H.U., K. Schmidt, B. Hopf, ECF
bleaching: Improving brightness stability
of kraft pulp. IPW/Papier, 2004; 6:
T105–T111.
70 Jaaskelainen, A.-S., et al., Characterization
of residual lignin structures by UV
Raman spectroscopy and the possibilities
of Raman spectroscopy in the visible
region with Kerr-gated fluorescence
rejection. In International Symposium
on Wood and Pulping Chemistry, Madison,
WI, 2003.
71 Fischer, K., Vergilbung von Hochausbeutezellstoff.
Das Papier, 1990;
44(10A): V11.
72 Eckert, R.C. US Patent 894561, 1978.
73 Jakara, J., A. Paren, J. Patola, Peroxide
activation – a key to high brightness in
TCF bleaching of softwood Kraft pulp.
In International Symposium on Wood
and Pulping Chemistry. Helsinki, Finland,
1995.
74 Hamalainen, H., et al., Mill scale application
of a molybdate activated peroxide
delignification process in ECF and TCF
production of softwood and hardwood
Kraft pulp. In International Symposium
on Wood and Pulping Chemistry. Madison,
WI, 2003.
75 Patt, R., T. Jaschinski, H.-J. Mielisch,
Stabilisierte und katalysierte Peroxidbleiche.
Wochenblatt fur Papierfabrikation,
1996; 17: 750–755.
76 Wieghardt, K., Die aktiven Zentren in
manganhaltigen Metallproteinen und
anorganische Modellkomplexe. Angew.
Chem., 1989; 101: 1179–1198.
77 Suess, H.U., J.D. Kronis, B. Taylor.
Selection of the best available technology
for TCF bleaching of sulfite pulp. In
Tappi Pulping Conference, 1998.
78 Wackerberg, E., et al., High temperature
peroxide stage optimization on hardwood
and softwood sulfite pulp. In
Tappi Pulping Conference, 1997.
79 Heimburger, S.A., K.F. French, N.
Weber. Optimizing pressurized peroxide
bleaching of a hardwood sulfite pulp. In
Tappi Pulping Conference, 1997.
80 Bottcher, H., R. Kamprath, Umweltfreundliche
Zellstofferzeugung auf
Basis des konventionellen Magnesium-
Bisulfit-Verfahrens. Das Papier, 1990;
44(10A): V26–V32.
81 Nimmerfroh, N., et al., The German
approach to the closed-cycle sulfite mill
– development and implementation.
Pulp Paper Canada, 1995; 96(12):
T414–T420.
82 Suess, H.U., K. Schmidt, M.d. Grosso.
Options to improve TCF-bleaching of
sulfite pulp. In 57th Appita Annual
Conference, Melbourne, Australia,
2003.
83 Sturm, W., Hochweisse Sulfitzellstoffe
durch absolut chlorfreie Bleiche – Aktivierung
von Peroxid durch Nitrilamin.
Wochenblatt fur Papierfabrikation, 1990;
118(10): 423–424.
84 Kuchler, J.G., W.G.J. Sturm,
H.E. Teichmann, Hohe Wei.grade und
deutlich bessere Delignifizierungsleistung
in der OPMgO-Stufe – Aktivierung
von Peroxid durch Nitrilamin (Teil 2).
Das Papier, 1993; 2: 53–55.
85 Kappel, J., M. Grengg, Brauer, Highconsistency
bleaching technology for
TCF pulps. Pulp Paper Canada, 1994;
95(1): T1–T6.
86 Sixta, H., et al., Medium consistency
ozone bleaching: laboratory and mill
experience. Das Papier, 1991; 45(10):
610–624.
87 Wickstrom, P., Improved brightness by
adding a peracetic acid stage. In International
Pulp Bleaching Conference,
Stockholm, Sweden, 2005: p. 216–221.
[aa] Kadla, J. F., H.-M. Chang, H. Jameel,
The Reactions of Lignins with High
Temperature Hydrogen Peroxide Part 2.
The Oxidation of Kraft Lignin. Holzforschung,
1999; 53(3): 277–284.
[bb] Kadla, J. F., H. M. Chang, Jameel, H.,
The reactions of lignins with hydrogen
peroxide at high temperature .1. The
oxidation of lignin model compounds.
Holzforschung, 1997; 51(5): 428–434.
Section 7.7
1 Ruohoniemi, K., et al. Experience in the
use of peracetic acid in ECF and TCF
bleaching. In International Pulp Bleaching
Conference, Helsinki, 1998.
References 931
2 Jakara, J., A. Paren, P. Autio. The use of
peracetic acid as a brightening agent. In
Appita Conference Proceedings, 1999.
3 Francis, R.C., et al., Caroate delignification
enhanced by halides. Tappi, 1994;
77(7): 135–141.
4 Suss, H.U., K. Schmidt, Generation of
halogenated compounds in bleaching
without chlorine. Can TCF be chlorinefree?
IPW/Papier, 2000; I(5): T69–T73.
Section 7.8
1 Marechal, A., Acid extraction of the alkaline
wood pulps (Kraft or Soda/AQ)
before or during bleaching, reason and
opportunity. J. Wood Chem. Technol.,
1993; 13(2): 261.
2 Teleman, A., et al., Characterization of
4-deoxy-b-L-threo-hex-4-enopyranosyluronic
acid attached to xylan in pine
kraft pulp and pulping liquor by 1H and
13C NMR spectroscopy. Carbohydrate
Res., 1995; 272: 55–71.
3 Li, J., G. Gellerstedt, The contribution to
kappa number from hexenuronic acid
groups in pulp xylan. Carbohydrate Res.,
1997; 302: 213–218.
4 Fengel, D., G. Wegener, Wood: chemistry,
ultrastructure, reactions. New York:
de Gruyter, 1983: 49, 109–112.
5 Vuorinen, T., et al., Selective hydrolysis
of hexeneuronic acid groups and its applications
in ECF and TCF bleaching of
kraft pulps. In International Pulp
Bleaching Conference. Washington,
1996.
6 Jiang, Z.-H., B.v. Lierop, R. Berry, Hexenuronic
acid groups in pulping and
bleaching chemistry. Tappi, 2000; 83(1):
167–175.
7 Gellerstedt, G., O. Dahlman. Recent
hypothesis for brightness reversion of
hardwood pulps. In International Colloquium
on Eucalyptus Kraft pulp. Universidade
Federal de Vicosa, MG, Brazil,
2003.
8 Ohlavi, P., V. Janne. Ozone bleaching
and AHL-stage acid treatment in a modern
multichemical bleach plant. In 35th
ABTCP Annual Conference. Sao Paolo,
Brazil, 2002.
Section 7.9
1 Viikari, L., Ranua, M., Kantelinen, A.,
Sundquist, J., Linko, M. 3rd International
Conference on Biotechnology in
the Pulp and Paper Industry, STFI,
Stockholm, 1986.
2 2,2′-azinobis(3-ethylbenzothiazoline-6-
sulfonic acid).
3 Call, H.P., PCT World Patent Application
No. WO 94/29510, 1994.
4 Call, H.P., PCT World Patent Application
No. WO 97/36041, 1997.
5 1-Hydroxybenzotriazole.
6 Galli, C., Gentili, P., J. Phys. Org. Chem.,
2004; 17: 973.
7 Call, H.P., Mucke, I., J. Biotechnol.,
1997; 53: 163.
8 Rochefort, D., Leech, D.,
Bourbonnais, R., Green Chem., 2004;
6: 14
9 Rochefort, D., Bourbonnais, R., Leech,
D., Renaud, S., Paice, M., J. Electrochem.
Soc., 2002; 149: D15.
10 ACS Symposium Series 785, Oxidative
Delignification Chemistry,
Argyropoulos, D.S. Ed., ACS, Washington,
2001.
11 Weinstock, I.A., Hill, C.L., US Patent
5,302,248, 1994.
12 Evtuguin, D.V., Pascoal Neto, C., Portuguese
Patent 101 857, 1996.
13 For more information on polyoxometalates
see: Polyoxometalates, Chem. Rev.,
1998; 98: 1.
14 Atalla, R.H., Weinstock, I.A., Bond, J.S.,
Reiner, R.S., Sonnen, D.M.,
Houtman, C.J., Heintz, R.A., Hill, C.G.,
Hill, C.L., Wemple, M.W., Geletii, Yu.V.,
Barbuzzi, E.M.G., Polyoxometalatebased
closed systems for oxidative
delignification of wood pulp fibers. In
ACS Symposium Series 785, Oxidative
Delignification Chemistry,
Argyropoulos, D.S. Ed., ACS, Washington,
2001: 313.
15 Weinstock, I.A., Barbuzzi, E.M.G.,
Wemple, M.W., Cowan, J.J., Reiner, R.S.,
Sonnen, D.M., Heintz, R.A., Bond, J.S.,
Hill, C.L., Nature, 2001; 414: 191.
16 Evtuguin, D.S., Pascoal Neto, C., Catalytic
oxidative delignification with Keggin-
type molybdovanadophosphate het932
7Pulp Bleaching
eropolyanions. In ACS Symposium Series
785, Oxidative Delignification
Chemistry, Argyropolous, D.S. Ed.,
ACS, Washington, 2001: 313.
Section 7.10
1 Suss, H.U., N. Nimmerfroh, Hydrogen
peroxide in chemical pulp bleaching.
ABTCP Meeting. Vitoria, Brazil, 1996.
2 Suss, H.U., Personal communication,
2004.
3 Annergren, G.E., M.G. Boman, P.E.
Sandstrom, Towards the closed cycle
bleach plant. 5th International Conference
on Newly Available Techniques.
Stockholm, Sweden, 1996.
4 Zolio, A., M.R. Silva, M.A.L. Peixoto,
Calcium oxalate scaling in bleach
plants: VCP experience. 33rd Pulp and
Paper Annual Congress. Sao Paulo, Brazil,
2000.
5 Reid, D.W., M.L. Hinck, Factors contributing
to calcium oxalate scale at the
Simpson Tacoma kraft mill. Tappi J.,
2003; 2(2): 8–13.
933
8
Pulp Purification
Herbert Sixta
8.1