- •Посвящается Лиле Секундант п редисловие
- •Раздел 1. Повелительные предложения
- •(10) Top disc диск верхней части, или верхний диск;
- •В некоторых словарях более старого издания такие
- •Обычно же в словаре их дают по так называемому гнездо-
- •Приставка un– дает слово с противоположным значением.
- •Поработайте сами. Проверьте себя по ключам в конце книги (см. The keys).
- •Итоговое упражнение I
- •Обещанный перечень глаголов
- •H to hang вешать
- •I to include включать в себя
- •Rto reach достигать, доставать to reduce уменьшать, сокращать
- •A action действие alignment совпадение осей; центровка
- •Bbalance равновесие; балансировка
- •Ddefect повреждение, неисправность
- •O oil масло
- •Раздел 2. Повествовательные предложения
- •Раздел 3. Страдательный залог.
- •Раздел 4. Грамматические трудности
- •Раздел 1
- •Раздел 2
- •Раздел 3
- •Раздел 4
Итоговое упражнение I
Bring the V belt pulley of the motor into exact alignment with the V belt pulley of the separator.
Apply a little grease or castor oil to the thread of screws C29 and put the screws into the holes in the bowl body.
Put gravity disc C3 with 72 mm hole diameter on the bowl hood.
From time to time screw out the drain screw some turns and draw an oil sample from the worm gear housing.
Clean nozzle C15 and channels C15A in the bowl body – see illustration on page 300-4.
Unscrew the small lock ring clockwise (tool V2) and exchange the gravity disc.
Screw out screws C26 and lift off spring support C25.
Insert the spindle in the tap, push on the slide and lock it with the slotted pin.
Measure the distance between surface ‘a’ of the paring disc and the upper plane of the height adjusting rings (‘h’ in the sketch).
Screw on the deflector anti-clockwise.
Push on the worm and lock it with the round nut.
Heat the ball bearing in oil and slip it over the spindle.
Fit the intermediate washer, screw on the round nut and secure it with the lock washer.
Screw out screws DA8 and lift the bowl spindle with spring casing straight up from the frame.
Fasten the disc of the tool to the nave with three of the screws of the coupling pulley.
Pull the conveyor pulley out of the frame together with worm wheel shaft, protecting cover and ball bearing.
Drive the pin out of stop ring E14.
Fasten packing with glue.
Check the ball bearings for defects.
Always place the packing ring with one of its holes right in front of the oil groove in the protecting cover.
For safety check also channels and valves in bowl body and operating slide.
Supply water shortly through hose 3.
Knock carefully on the board right above the ring, first on one side then on the other.
Turn the board around successively and drive the ring into the groove as evenly as possible.
Обещанный перечень глаголов
A to absorb поглощать
to accomplish завершать
to adapt приспосабливать
to adjust регулировать
to admit принимать, впускать
to apply применять, прилагать; наносить
to assemble собирать
B to back сдавать назад
to balance уравновешивать
to be быть, являться, находиться
to bend наклонять, изгибать
to break ломать
to bring приносить
to brush чистить щеткой
to build up возрастать
C to carry нести
to carry out выполнять
to cause вызывать, быть причиной
to check проверять
to clamp зажимать
to clarify осветлять
to clean чистить, очищать
to come приходить
to complete завершать
to compress сжимать
to conduct проводить
to consult советоваться, справляться
to convert превращать
to correspond соответствовать
to count считать, пересчитывать
to cover закрывать
to cut резать, разрезать, вырубать
D to damage повреждать
to decrease уменьшать
to deliver доставлять
to deposit отлагать, осаждать(ся)
to determine устанавливать, определять
to discharge выливать, отводить, спускать
to dismantle разбирать
to displace смещать, сменять, вытеснять
to distribute распределять, распространять
to divide разделять, делить
to drain осушать, спускать (воду, масло)
to draw тащить, снимать
to drive приводить в движение
E to engage сцепляться
to equalize уравновешивать
to establish устанавливать
to exceed превышать
F to facilitate облегчать, продвигать
to fasten закреплять
to fill наполнять
to fit пригонять, монтировать
to fix устанавливать, прикреплять
to flow течь
G to generate производить, вызывать
to give давать
to glide скользить