More6.4_rus_UG(руководство)

234

Error

Water density indicates use of wrong unit system

235

Warning

Value outside expected range:

250

Warning

WATR density and viscosity taken from built-in correlations when

STEAM used

251

Warning

Water enthalpy taken from built-in correlations when STEAM used

252

Warning

Water expansion obtained from built-in correlations when STEAM

used

260

Error

Too many TEMP values for EoS mode

261

Error

DUPL not allowed on first TEMPerature"

301

Error

Table not found

302

Error

Error in oil saturation functions

303

Error

Error in gas saturation functions

304

Error

Error in water saturation functions

305

Error

Error in KVSP functions

306

Error

Error in KRGO saturation functions

307

Error

Error in KRWO saturation functions

308

Error

Error in OVVT functions

320

Error

Likely error: use ZERO keyword to permit zero connate water

321

Error

Kro>0.0 at zero Soil using Stone II - see OUT file

322

Error

No KRGO base table for SCAL

323

Error

No KRWO base table for SCAL

324

Error

Attempt to use SCALE with no KRGO or KRWO base tables

325

Error

SCALE needs equal number of KRGO and KRWO tables defined

326

Error

Sgmax in ADJU no longer supported: set Swl using KRWO or WSF

401

Error

Dimension error in uniform coarsening

402

Error

Dimension error in non-uniform coarsening

403

Error

Total number of cells in CXGR must equal fine grid dimension

404

Error

Total number of cells in CYGR must equal fine grid dimension

405

Error

Total number of cells in CZGR must equal fine grid dimension

407

Error

Faults cannot be set up after grid calculations done

408

Error

Problem dimensions should be positive

410

Error

Error reading Roff file

411

Error

SIZE must be read before keyword

412

Error

Too many user defined arrays, limit is

413

Error

Number of data items for triplet data must be divisible by 3

414

Error

No areal cell position data - cannot interpolate

415

Error

NOXY specified but x/y values not yet specified

416

Error

No x-location data entered with LINE

417

Error

No y-location data entered with LINE

418

Error

Must be CONTinuous array, i.e. dimensioned to (Nx+1)*(Ny+1)

419

Error

Must be a DISC/DISC, DISC/CONT or CONT/CONT specification

420

Error

Local grid already exists:

421

Error

No local grid name found

422

Error

Limit on REFI nesting levels

423

Error

x-interval must contain at least one cell for local grid

424

Error

y-interval must contain at least one cell for local grid

425

Error

z-interval must contain at least one cell for local grid

426

Error

x-dimension must be multiple of global x-extent in local grid

427

Error

y-dimension must be multiple of global y-extent in local grid

428

Error

z-dimension must be multiple of global z-extent in local grid

429

Error

Name of fault must be specified with FAUL

430

Error

Argument must be TO_I, TO_I, TO-J or TO_J

431

Error

User fault not found

432

Error

No SIZE keyword found

433

Error

LAYE defined before SIZE or SPEC keyword found

434

Error

LAYE defined in LGR - only allowed for global grid

435

Error

Wrong layer total in LAYE:

436

Error

XDIV defined before SIZE or SPEC keyword found

437

Error

YDIV defined before SIZE or SPEC keyword found

438

Error

XDIV defined in LGR - only allowed for global grid

439

Error

YDIV defined in LGR - only allowed for global grid

440

Error

Wrong row total in XDIV:

441

Error

Wrong row total in YDIV:

442

Error

Array not found

443

Error

Fault segment in x-direction must have IX1=IX2

444

Error

Fault segment in y-direction must have IY1=IY2

445

Error

Fault segment in z-direction must have IZ1=IZ2

446

Error

CONT not available with MODI/REPL

447

Error

DISC not available with MODI/REPL

448

Error

9 arguments expected with TCON

449

Error

Grid data cannot be entered after grid calculations done (except

PVOL,DEPT,TX,TY and TZ)

460

Error

Number of non-uniform coarsening groups not set

461

Error

Too few coarsening numbers supplied

462

Error

Coarsening data must be entered in the INPU section

463

Error

Size of box with REPLace must be positive

464

Error

Refinment and coarsening not allowed together

465

Error

Local grid not found:

466

Error

Three coarsening factors expected with COAR

470

Warning

Cell inverted

471

Warning

Cells overlap

480

Warning

Only one value required for UNIForm input

481

Warning

Negative K_X found: set to zero

482

Warning

Negative K_Y found: set to Kx

483

Warning

Negative K_Z found: set to Kx

484

Warning

Non-integer table index:

485

Warning

Fewer COOR values than expected:

486

Warning

Fewer ZCOR values than expected:

487

Error

Too few values supplied with REPLace:

488

Error

Too few values supplied with LINEear:

501

Error

Aquifer depth must be set

502

Error

Aquifer permeability must be set

503

Error

Aquifer porosity must be set

504

Error

Aquifer compressibility must be set

505

Error

Aquifer radius must be set

506

Error

Aquifer thickness must be entered

507

Error

Unable to find aquifer

508

Error

Unable to find aquifer

509

Error

Too few lines of EQUI data

510

Warning

Too many lines of EQUI data

511

Error

Error in equilibration region

512

Error

Flip region not found

513

Warning

CONST Swat less than connate

514

Error

No pressures set in F(DE table

515

Error

Initialisation error

516

Error

Error in bubble point vs depth data:

517

Error

Error in Rv vs depth data:

518

Error

No bubble points set in F(DE table column 3

519

Error

CBM error

520

Error

Gas-oil contact below water-oil contact:

525

Error

No valid rows of data in F(DE table"

528

Error

Limit (10) on number of separators reached

529

Warning

Default separator conditions used: EoS flash to standard conditions

530

Error

Pressure value required in CONS-no default available

531

Error

Bubble point value required in CONS-no default available

532

Error

EQUI entered with NONEquilibrium initialisation

601

Error

Unable to find well

602

Error

Unable to find group

603

Error

Unable to find limit

604

Warning

No wells found to add to group

605

Error

No injection fluid recognised for well

606

Warning

Action applies to rate limits only

610

Error

No datum depth for TUBI table

611

Error

Cannot set flows after bhp values for TUBI table

612

Error

Cannot set thps after bhp values for TUBI table

613

Error

Cannot set ratios after bhp values for TUBI table

614

Error

TUBI ratio must be wor,wct,wcut,wgr,gor,glr,ogr,cgr table

615

Error

Unable to recognise TUBI subkeyword

616

Warning

Well name will be truncated to 16 characters on output files

619

Warning

No completion interval for track table:

620

Error

Measured depth interval must be set with COMPLETE

621

Error

Unable to find welltrack

622

Error

ZONE should not be used with CIJK and COMP

623

Error

Well cannot be completed in more than one way, already used

624

Warning

Cell refined: completion in refinement required:

625

Warning

Comp measured depth interval not within track:

626

Warning

LOCA used as well as CIJK - LOCA ignored

627

Warning

LOCA used as well as COMP - LOCA ignored

628

Warning

LOCA used as well as DEVI - LOCA ignored

629

Warning

LOCA used as well as HORI - LOCA ignored

630

Error

No location information for well

631

Error

Date out of order in HFIL table

632

Error

No historical data found for well

648

Warning

Group fraction greater than 1 in group

649

Error

Group fraction less than zero in group

657

Warning

No action specified for GLIM so target assumed for group

660

Warning

No injection steam properties specified for well

670

Error

One of the first 4 PRIOrity numerator coefficients must be non-zero

671

Error

One of the last 4 PRIOrity denominator coefficients must be non-

zero

681

Error

Could not recognise descriptor (must be DD,MM,MMM,YY or

YYYY)

682

Error

Could not recognise descriptor (must be QOIL..BHP)

680

Error

Could not find 3 date descriptors in string

681

Error

Could not recognise descriptor (must be DD,MM,MMM,YY or

YYYY)

682

Error

Could not recognise descriptor (must be QOIL..BHP)

683

Error

TARG no longer available: please use SALE

684

Error

TARG no longer available: please use MAKE

685

Error

BOUN no longer available: please use SALE

686

Error

BOUN no longer available: please use MAKE

690

Error

Pump table not found

691

Warning

Flip region not found

692

Warning

Well efficiency factor outside usual range (0.0 to 1.0)

693

Warning

Well datum depth gives negative bhp target

697

Warning

Attempt to advance to before initial time

698

Warning

Attempt to advance to earlier time

699

Error

No progress on minimum timestep