Хорошев / ИЛП_материал_маг_02.15 / DEF STAN 00-60 / Issue 4 / Part 0 - Appendix F to Annex C - Data element dictionary

DEF STAN 00-60 (PART 0)/4

APPENDIX F TO ANNEX C

A code used to indent item names in the repair part description column in a manual to depict disassembly parts relationship within a figure of the text. Codes are: ‘1’ through ‘5’, which indents the item in the parts manual listing by the number specified.

The technical manual, technical order or manual controlling number assigned by the Project.

INTEROPERABLE ITEM TECHNICAL MANUAL NUMBER. The technical manual number for the interoperable item.

A one-position code specifying a ratio. The TAR is determined by dividing the maximum permitted error of the unit to be measured or calibrated by the maximum known error of the measuring or generating device used to perform the measurement. The codes can be used for the desired TAR or the actual TAR.

SE UUT PARAMETER TAR DESIRED. The desired TAR of the TMDE in conjunction with the SE UUT.

SE UUT PARAMETER TEST ACCURACY RATIO ACTUAL. The actual TAR of the TMDE in conjunction with the SE UUT.

UUT PARAMETER TAR DESIRED. The desired TAR of the TMDE in conjunction with the UUT.

UUT PARAMETER TEST ACCURACY RATIO ACTUAL. The actual TAR of the TMDE in conjunction with the UUT.

C/F-169

DEF STAN 00-60 (PART 0)/4

APPENDIX F TO ANNEX C

The language used for expressing the test specifications and procedures. The particular test-oriented language, used in the preparation and documentation of test procedures, independent of particular test equipment used. A test language can be implemented either manually or with automatic or semiautomatic test equipment.

444 TEST MEASUREMENT AND DIAGNOSTIC EQUIPMENT 1 A F - REGISTER CODE (TMDE CODE)

A code which further defines the TMDE Register Index Number. Codes are as follows:

445 TEST MEASUREMENT AND DIAGNOSTIC EQUIPMENT 7 X F - REGISTER INDEX NUMBER

A seven digit index number assigned to each item in the TMDE register.

Land Systems: See AESP-6625-A316 Compendium of Electronic Test Equipment (ETE), EMER T&M A317 Register of ETE, EMER T&M A318 Register of Mechanical Equipment.

Air Systems: See AP100C-50.

A single-letter code indicating whether test points are available on the support/test equipment to test for integrity utilizing additional support/test equipment.

A single-letter code indicating whether the fault isolated replaceable unit has a test requirements document assigned to it.

C/F-170

DEF STAN 00-60 (PART 0)/4

APPENDIX F TO ANNEX C

The number assigned to the Test Requirements Document.

SE UUT TEST REQUIREMENTS DOCUMENT NUMBER. A TRD number of the support equipment unit under test.

UUT TEST REQUIREMENTS DOCUMENT NUMBER. A TRD number of the unit under test.

A code used to sequence text within the applicable Text Data Element Definitions. Codes begin with ‘1’ and continue through ‘99999’.

ADDITIONAL REQUIREMENTS TEXT SEQUENCING CODE. A TSC used with additional requirements narrative.

AMMUNITION TYPE NARRATIVE TEXT SEQUENCING CODE. A TSC used with the ammunition type narratives.

BASELINE FACILITY NARRATIVE TEXT SEQUENCING CODE. A TSC used with baseline facility narratives.

FACILITY NARRATIVE TEXT SEQUENCING CODE. A TSC used with facility narratives.

FAILURE MODE AND RCM NARRATIVE TEXT SEQUENCING CODE. A TSC used with failure and Reliability-Centred Maintenance narratives.

FAILURE MODE INDICATOR MISSION PHASE CHARACTERISTICS NARRATIVE TEXT SEQUENCING CODE. A TSC used with failure mode/mission narratives.

NEW OR MODIFIED FACILITY NARRATIVE TEXT SEQUENCING CODE. A TSC used with new or modified facility narratives.

NEW OR MODIFIED SKILL NARRATIVE TEXT SEQUENCING CODE. A TSC used with new or modified skill narratives.

PARTS MANUAL TEXT SEQUENCING CODE. A TSC used with provisioning nomenclature.

PROVISIONING TEXT SEQUENCING CODE. A TSC used with provisioning narratives.

C/F-171

DEF STAN 00-60 (PART 0)/4

APPENDIX F TO ANNEX C

PHYSICAL AND MENTAL REQUIREMENTS TEXT SEQUENCING CODE. A TSC used with physical and mental requirements.

RAM CHARACTERISTICS NARRATIVE TEXT SEQUENCING CODE. A TSC used with reliability, availability, and maintainability characteristics narratives and software narratives.

SEQUENTIAL SUBTASK DESCRIPTION TEXT SEQUENCING CODE. A TSC used with subtask narratives.

SERD REVISION TEXT SEQUENCING CODE. A TSC used with SERD revision remarks.

SUPPORT EQUIPMENT NARRATIVE TEXT SEQUENCING CODE. A TSC used with each of the SE narratives.

SYSTEM END ITEM NARRATIVE TEXT SEQUENCING CODE. A TSC used with system end item narratives.

TASK/SUBTASK ASSOCIATED NARRATIVE TEXT SEQUENCE CODE. A TSC used with task/subtask associated narratives.

TRANSPORTED END ITEM NARRATIVE TEXT SEQUENCING CODE. A TSC used with transported end item narratives.

TRANSPORTATION NARRATIVE TEXT SEQUENCING CODE. A TSC used with transportation narratives.

UUT EXPLANATION TEXT SEQUENCING CODE. A TSC used with Unit Under Test narrative.

C/F-172

DEF STAN 00-60 (PART 0)/4

APPENDIX F TO ANNEX C

A recommended quantity of an item required to support a specific number of applications for a specific period of time. The applications may be to a weapon system, end item, component or combinations thereof, which are contained in the applicable contract.

The total number of systems intended for operational use.

The maximum towing speed of the system/equipment in Kilometres per hour.

Specify the ground pressure created by the heaviest pad. Unit of Measure to be specified by Project.

A numeric value describing the size of the tracked shoe pad actually in contact with the ground of the transported item in units contained in the associated UM.

The number of tracked shoe pads actually in contact with the ground.

The weight in kg supported by the road wheel of the tracked item.

The cost of training a single SSC, used with an associated Currency Code (DED 629).

Denotes any of the following reasons for recommending the training location to be classroom or on job training:

C/F-173

DEF STAN 00-60 (PART 0)/4

APPENDIX F TO ANNEX C

Denotes any of the following reasons for recommending training for a task:

Training required due to task frequency; ie, the task might rate low for training priority if it is rarely performed.

Points to the need for selecting tasks for training that are essential to job performance. Consequences of inadequate performance on certain tasks could result in injury to personnel, loss of life, or damage to equipment.

A measure of how much delay can be tolerated between the time the need for task performance becomes evident and the time actual performance shall begin. This is based upon known time constraints associated with the equipment, which, if ignored, will result in equipment loss or damage, eg, loss of power to a computer shall be restored within a set time interval or stored memory is lost.

The learning difficulty of a task refers to the time, effort, and assistance required to achieve performance proficiency.

Used to ensure that training is given in those essential job skills in which job incumbents frequently perform poorly.

The criteria of the immediacy of performance are:

1.Whether or not there is a high probability of the graduate encountering the task on the job within the first year after training.

2.The predicted or measured amount of decay of the skill that will take place during the time interval.

C/F-174

DEF STAN 00-60 (PART 0)/4

APPENDIX F TO ANNEX C

Points to the need for training tasks that are most often performed on the job.

Points to a need for providing training to assist job incumbents in efficient performance of those tasks on which they spend the most time.

Training required due to task frequency, eg, the task is infrequent but performance is critical.

The job incumbent will be expected to be proficient in the task immediately, eg, a digital post with no hand-over period.

A single-position code indicating when a task is recommended for training and what type of training is needed. Training, in this context, does not include equipment familiarization.

A code which describes how the system/equipment can be transported.

C/F-175

DEF STAN 00-60 (PART 0)/4

APPENDIX F TO ANNEX C

A code which identifies each different way that a system/equipment can be transported. This is a numeric character assigned in sequence.

The cost per kilogram per kilometre or mile, used with an associated Currency Code (DED 629), as specified by the Project for transportation of material.

A code that signifies whether the LCN represents a system/end item requiring transportation requirements documentation.

A code that signifies whether the shipping modes for the item or the transport end items itself is being analyzed.

C/F-176

Narrative explanation of the projection points of the item to be transported.

472 TRANSPORTATION REMARKS (HANDLING, TOWING, 65 X - - AIR DROP SELF-PROPELLED)

Narrative explanation of any of the handling characteristics, towing characteristics, selfpropelled characteristics, or air drop information.

A code which differentiates each mobility type. This is a sequentially assigned number beginning with 1 through 99.

Narrative explanation of any equipment being transported other than wheeled, tracked, or skid mounted.

Narrative explanation of where the item is being transported to and from.

For wheeled vehicles only, in narrative format the 90 degree and 180 degree turning radius in both wall-to-wall and curb-to-curb.

C/F-177

DEF STAN 00-60 (PART 0)/4

APPENDIX F TO ANNEX C

A single-position code which indicates the status of a material support system in relation to its overall life history as a guide to procurement, authorization, logistical support, asset, and readiness reporting.

A government supplied code identifying an end item in the maintenance data collection sub-system (MDCS) by its application to the specific type/model/series of aircraft or equipment which it supports.

Sea Systems: Codes equate to class of vessel.

Air Systems: Codes allocated by RAF Logistic Support Services 4 (LSS4/MACD).

This block, which is blank on initial submissions of provisioning data, shall be used as a type of change code to indicate deletions, modifications, typographical errors, quantity changes (increase, decrease), and limited part applications as follows:

C/F-178