- •3.1. Природа и основные параметры взаимного влияния между цепями
- •3.1 The nature and Main Parameters of the Interaction Between Circuits
- •Лекция № 4 Lecture # 4
- •3.4. Основное уравнение влияния между цепями
- •3.4. Basic equation of influence between the circuits
- •Лекция № 5 Lecture # 5
- •3.5. Зависимость переходного затухания от частоты и длины
- •3.5. Dependence of transient attenuation from frequency and line length
- •Лекция № 7 Lecture # 7
- •3.7. Влияния в коаксиальных кабелях
- •3.7. Influences in the coaxial cables
- •Frequency
- •3.11. Меры защиты от взаимных влияний
- •3.11. Protective measures from interactions
- •3.13. Симметрирование методом скрещивания
- •3.13. Transposition method for balansing
- •3.14. Конденсаторное симметрирование
- •3.14. Capacitory balancing
- •3.15. Концентрированное симметрирование
- •3.15. Concentrated balancing
- •3.17. Симметрирование высокочастотных кабелей
- •3.17. Balancing of the high-frequency cables
- •3.18. Симметрирование вЧ кабелей по комплексным
- •3.18. Balancing of the high-frequency cables by complex couplings
- •3.19. Этапы симметрирования вЧ кабелей
- •3.19. Stages of the high-frequency cables balancing
3.19. Этапы симметрирования вЧ кабелей
3.19. Stages of the high-frequency cables balancing
а60
Законченным объектом симметрирования кабелей является усилительный участок системы К-60. Симметрирование высокочастотных кабелей выполняется в два этапа: при монтаже строительных длин кабеля между собой и на смонтированном усилительном участке.
При монтаже строительных длин кабеля производят систематическое скрещивание первой цепи четверки в каждой муфте по оператору Х • •. Это позволяет уменьшить систематические влияния через третьи цепи кабеля и повысить эффективность последующего концентрированного симметрирования.
На смонтированном усилительном участке осуществляют концентрированное симметрирование, т. е. вначале производят скрещивание, а затем цепи, не удовлетворяющие нормам, симметрируют путем включения контуров противосвязи.
Концентрированное симметрирование выполняется одновременно в трех муфтах усилительного участка (1/4L, 2/4L, 3/4L), контуры противосвязи подбираются преимущественно по результатам измерения защищенности на дальнем конце с помощью приборов ВИЗ или КИПЗ.
Симметрирование осуществляется на максимальной частоте 252 кГц с последующим контролем при более низких частотах 200, 150, 100, 50 кГц. Величина защищённости должна быть не менее 73,8 дБ.
Система симметрирования ВЧ кабелей приведена в таблице 3.5.
The completed object of the cable balancing is K-60 system repeater section. The balancing procedure of еру HF cables has to be done in two stages: when the construction lengths are mounted together and on the ready-mounted repeater section.
When mounting the cable construction there is regularly wire transposition of the first circuit quad in each adapter by the operator X • • are. This allows to decrease the systematic influences through of the third circuits and to increase the effectiveness of the following concentrated balancing.
On the ready-mounted repeater section is realized concentrated balancing, that is, at first produce the transposition, and then the circuit, which do not meet the standards are balanced by the insertion of the counter-coupling circuits.
Concentrated balancing is performed simultaneously in the three adapters of the amplifier section (1/4L, 2/4L, 3/4L), the counter-coupling circuit selected mainly on results of the measurement of the protectability at the far end with ВИЗ or КИПЗ devices.
The balancing procedure is performed on the maximum frequency 252 kHz with checking on the frequencies 200, 150, 100, 50 kHz. The value of protectability must be not less then 73.8 dB.
System balancing of the HF cable is shown in Table 3.5.
Table 3.5. Balancing system for HF cables
Balancing stage |
Protectability values to be measured |
Balancing method |
Standard |
Balancing location |
Notes |
In the each adapters |
Without measurement |
The transposition of one circuit by X • • operator |
-- |
In the each adapters |
|
On the ready-mounted section |
On the far end |
The transposition
|
The maximum value |
1/4, 2/4, 3/4 of repeater section |
Balancing on the 252 kHz, checking – on the 50, 100, 150, 200 kHz |
|
On the far end |
The counter-coupling circuit
|
73,8 dB (8,5 Np) |
1/4, 2/4, 3/4 of repeater section |
Balancing on the 252 kHz, checking – on the 50, 100, 150, 200 kHz |