
- •Revision History
- •1.1 Features
- •2 Introduction
- •2.1 Description
- •2.2 Pin Assignments
- •2.2.1 Ball Grid Array (GZZ and ZZZ)
- •2.2.3 Signal Descriptions
- •3 Functional Overview
- •3.1 Memory
- •3.1.3 Instruction Cache
- •3.1.4 Memory Map
- •3.1.5 Boot Configuration
- •3.2 Peripherals
- •3.3 Configurable External Ports and Signals
- •3.3.1 Parallel Port Mux
- •3.3.2 Host Port Mux
- •3.3.3 Serial Port 2 Mux
- •3.3.4 External Bus Selection Register (XBSR)
- •3.4 Configuration Examples
- •3.5 Timers
- •3.5.1 Timer Interrupts
- •3.5.2 Timer Pins
- •3.5.3 Timer Signal Selection Register (TSSR)
- •3.6 Universal Asynchronous Receiver/Transmitter (UART)
- •3.9 Direct Memory Access (DMA) Controller
- •3.9.1 DMA Channel 0 Control Register (DMA_CCR0)
- •3.10 System Clock Generator
- •3.10.1 Input Clock Source
- •3.10.2 Clock Groups
- •3.10.3 EMIF Input Clock Selection
- •3.10.4 Changing the Clock Group Frequencies
- •3.10.5 PLL Control Registers
- •3.10.6 Reset Sequence
- •3.11 Idle Control
- •3.11.1 Clock Domains
- •3.11.2 IDLE Procedures
- •3.11.3 Module Behavior at Entering IDLE State
- •3.11.4 Wake-Up Procedure
- •3.11.5 Auto-Wakeup/Idle Function for McBSP and DMA
- •3.11.6 Clock State of Multiplexed Modules
- •3.11.7 IDLE Control and Status Registers
- •3.12 General-Purpose I/O (GPIO)
- •3.13 External Bus Control Register
- •3.13.1 External Bus Control Register (XBCR)
- •3.14 Internal Ports and System Registers
- •3.14.1 XPORT Interface
- •3.14.2 DPORT Interface
- •3.14.3 IPORT Interface
- •3.14.4 System Configuration Register (CONFIG)
- •3.15 CPU Memory-Mapped Registers
- •3.16 Peripheral Registers
- •3.17 Interrupts
- •3.17.1 IFR and IER Registers
- •3.17.2 Interrupt Timing
- •3.17.3 Interrupt Acknowledge
- •3.18 Notice Concerning TCK
- •4 Support
- •4.1 Notices Concerning JTAG (IEEE 1149.1) Boundary Scan Test Capability
- •4.1.1 Initialization Requirements for Boundary Scan Test
- •4.1.2 Boundary Scan Description Language (BSDL) Model
- •4.2 Documentation Support
- •5 Specifications
- •5.1 Electrical Specifications
- •5.3 Recommended Operating Conditions
- •5.5 Timing Parameter Symbology
- •5.6 Clock Options
- •5.6.1 Internal System Oscillator With External Crystal
- •5.6.2 Layout Considerations
- •5.6.3 Clock Generation in Bypass Mode (APLL Disabled)
- •5.6.4 Clock Generation in Lock Mode (APLL Synthesis Enabled)
- •5.6.5 EMIF Clock Options
- •5.7 Memory Timings
- •5.7.1 Asynchronous Memory Timings
- •5.7.2 Programmable Synchronous Interface Timings
- •5.7.3 Synchronous DRAM Timings
- •5.8 HOLD/HOLDA Timings
- •5.9 Reset Timings
- •5.10 External Interrupt and Interrupt Acknowledge (IACK) Timings
- •5.11 XF Timings
- •5.12 General-Purpose Input/Output (GPIOx) Timings
- •5.13 Parallel General-Purpose Input/Output (PGPIOx) Timings
- •5.14 TIM0/TIM1/WDTOUT Timings
- •5.14.1 TIM0/TIM1/WDTOUT Timer Pin Timings
- •5.14.3 TIM0/TIM1/WDTOUT Interrupt Timings
- •5.15 Multichannel Buffered Serial Port (McBSP) Timings
- •5.15.1 McBSP Transmit and Receive Timings
- •5.15.3 McBSP as SPI Master or Slave Timings
- •5.16 Host-Port Interface Timings
- •5.16.1 HPI Read and Write Timings
- •5.16.3 HPI.HAS Interrupt Timings
- •5.17 Inter-Integrated Circuit (I2C) Timings
- •5.18 Universal Asynchronous Receiver/Transmitter (UART) Timings
- •6 Mechanical Data
- •6.1 Package Thermal Resistance Characteristics
- •6.2 Packaging Information

TMS320VC5502
Fixed-Point Digital Signal Processor
www.ti.com
SPRS166J –APRIL 2001 –REVISED AUGUST 2006
3.1.5Boot Configuration
The on-chip bootloader provides a way to transfer application code and tables from an external source to the on-chip RAM at power up. The 5502 provides several options to download the code to accommodate varying system requirements. These options include:
∙Host-port interface (HPI) boot, both in multiplexed and non-multiplexed modes
∙External memory boot (via EMIF) from 16-bit asynchronous memory
∙Serial port boot (from McBSP0) with 16-bit element length
∙SPI EPROM boot (from McBSP0) supporting EPROMs with 24-bit addresses
∙I2C EPROM boot (from I2C) supporting EPROMs larger than 512K bits
∙UART boot
∙Direct execution (no boot) from 16or 32-bit external asynchronous memory
The external pins BOOTM2, BOOTM1, and BOOTM0 select the boot configuration. The values of BOOTM[2:0] are latched with the rising edge of the RESET input. BOOTM2 is shared with GPIO2, BOOTM1 is shared with GPIO1, and BOOTM0 is shared with GPIO0.
The boot configurations available are summarized in Table 3-3.
|
Table 3-3. Boot Configuration Selection Via the BOOTM[2:0] Pins |
BOOTM[2:0] |
BOOT PROCESS |
000 |
Direct execution from 16-bit external asynchronous memory |
001 |
SPI EPROM boot |
010 |
Serial port boot (from McBSP0) |
011 |
External memory boot (via EMIF) from 16-bit asynchronous memory |
100 |
Direct execution from 32-bit external asynchronous memory |
101 |
HPI boot |
110 |
I2C EPROM boot |
111 |
UART boot |
3.2Peripherals
The 5502 includes the following on-chip peripherals:
∙An external memory interface (EMIF) (1)
–Supporting a 32-bit interface to asynchronous memory, SDRAM, and SBSRAM
∙A host-port interface (HPI) (1)
–Configurable to 8 bits (multiplexed mode) or 16 bits (non-multiplexed mode)
∙A six-channel direct memory access (DMA) controller
∙Three multichannel buffered serial ports (McBSPs)
∙A programmable analog phase-locked loop (APLL) clock generator
∙General-purpose I/O (GPIO) pins and a dedicated output pin (XF)
∙Four timers
–Two 64-bit general-purpose timers
–A programmable watchdog timer
–A DSP/BIOS timer
∙An Inter-integrated Circuit (I2C) multi-master and slave interface
∙A Universal Asynchronous Receiver/Transmitter (UART)
(1)The 5502 can be configured as follows:
∙32-bit external memory interface with 8-bit (multiplexed) host-port interface
∙no external memory interface with 16-bit (non-multiplexed) host-port interface
Submit Documentation Feedback |
Functional Overview |
35 |