- •1 General
- •1.1 Scope
- •1.2 Conformance and references
- •1.3 Definitions
- •1.4 Acronyms
- •1.5 Symbols
- •1.6 Conventions
- •1.6.1 Cross references
- •1.6.2 Informative text
- •1.6.3 Terms in capitals
- •1.6.4 Notation of numbers
- •1.6.5 Units of physical quantities
- •1.6.6 Bit ordering in a byte
- •1.6.7 Byte numbering
- •1.7 Operators
- •1.7.1 Exclusive-OR
- •1.7.2 Concatenation
- •2 Power Transmitter Designs
- •2.1.1 Power Transmitter design A10
- •2.1.1.1 Mechanical details
- •2.1.1.1.1 Primary Coil
- •2.1.1.1.2 Shielding
- •2.1.1.1.3 Interface Surface
- •2.1.1.1.4 Alignment aid
- •2.1.1.1.5 Inter coil separation
- •2.1.1.2 Electrical details
- •1 General
- •1.1 Scope
- •1.2 Conformance and references
- •1.3 Definitions
- •1.4 Acronyms
- •1.5 Symbols
- •1.6 Conventions
- •1.6.1 Cross references
- •1.6.2 Informative text
- •1.6.3 Terms in capitals
- •1.6.4 Notation of numbers
- •1.6.5 Units of physical quantities
- •1.6.6 Bit ordering in a byte
- •1.6.7 Byte numbering
- •1.7 Operators
- •1.7.1 Exclusive-OR
- •1.7.2 Concatenation
- •2 Power Transmitter Designs
- •2.1.1 Power Transmitter design A11
- •2.1.1.1 Mechanical details
- •2.1.1.1.1 Primary Coil
- •2.1.1.1.2 Shielding
- •2.1.1.1.3 Interface Surface
- •2.1.1.1.4 Alignment aid
- •2.1.1.1.5 Inter coil separation
- •2.1.1.2 Electrical details
- •1 General
- •1.1 Scope
- •1.2 Conformance and references
- •1.3 Definitions
- •1.4 Acronyms
- •1.5 Symbols
- •1.6 Conventions
- •1.6.1 Cross references
- •1.6.2 Informative text
- •1.6.3 Terms in capitals
- •1.6.4 Notation of numbers
- •1.6.5 Units of physical quantities
- •1.6.6 Bit ordering in a byte
- •1.6.7 Byte numbering
- •1.7 Operators
- •1.7.1 Exclusive-OR
- •1.7.2 Concatenation
- •2 Power Transmitter Designs
- •2.1.1 Power Transmitter design B4
- •2.1.1.1 Mechanical details
- •2.1.1.1.1 Primary Coil array
- •2.1.1.1.2 Shielding
- •2.1.1.1.3 Interface Surface
- •2.1.1.2 Electrical details
- •2.1.1.3 Scalability
|
System Description |
|
Wireless Power Transfer |
Version 1.1 Addendum B4 |
General |
1 General
1.1Scope
Volume I of the System Description Wireless Power Transfer consists of the following documents:
Part 1, Interface Definition.
Part 2, Performance Requirements.
Part 3, Compliance Testing.
This document defines the addition of a new Power Transmitter design. The material contained in this document will be integrated into Part 1 of Volume I of the System Description Wireless Power Transfer, at some later time.
1.2Conformance and references
All specifications in this document are mandatory, unless specifically indicated as recommended or optional or informative. To avoid any doubt, the word “shall” indicates a mandatory behavior of the specified component, i.e. it is a violation of this System Description Wireless Power Transfer if the specified component does not exhibit the behavior as defined. In addition, the word “should” indicates a recommended behavior of the specified component, i.e. it is not a violation of this System Description Wireless Power Transfer if the specified component has valid reasons to deviate from the defined behavior. And finally, the word “may” indicates an optional behavior of the specified component, i.e. it is up to the specified component whether to exhibit the defined behavior (without deviating there from) or not.
In addition to the specifications provided in this document, product implementations shall also conform to the specifications provided in the System Descriptions listed below. Moreover, the relevant parts of the International Standards listed below shall apply as well. If multiple revisions exist of any System Description or International Standard listed below, the applicable revision is the one that was most recently published at the release date of this document. Moreover, if there exist addendum documents to the applicable revision, such addendum documents are considered to be an integral part of that applicable revision.
[Part 1] |
System Description Wireless Power Transfer, Volume I, Part 1, Interface |
|
Defintion. |
[Part 2] |
System Description Wireless Power Transfer, Volume I, Part 2, Performance |
|
Requirements. |
[Part 3] |
System Description Wireless Power Transfer, Volume I, Part 3, Compliance |
|
Testing. |
[SI] |
The International System of Units (SI), Bureau International des Poids et |
|
Mesures. |
1.3Definitions
This document introduces no new definitions to the System Description Wireless Power Transfer.
1.4Acronyms
This document introduces no new acronyms to the System Description Wireless Power Transfer.
1.5Symbols
This document introduces no new symbols to the System Description Wireless Power Transfer.
© Wireless Power Consortium, May 2012 |
1 |