Hectors 40ph pm alternator

2005-05-02, © ARKResearch public disclosure 2005

You can create a 40 phase’s recovery bridge by positive and negative connections to each commutator segment so it can operate on a 40 phases delta grid , its an application missed in the chorus motor patent as they were not bridged for recovery

Below is a Multi phase motor generator prototype pics using external PM rotor.

A positive and negative diode goes to each segment creating simile to 3 phases bridge with a 40 Phases delta rectified circuit all wires length must be EQUAL to valance diode currents and current collector points must be all drift compensated in order to avoid cross current losses.

	alt40ph06 - diode array direction
	alt40ph08 - magnets
alt40ph19- 2.7ohms at 180deg.jpg

ORIGINAL COMMENTS:

In 40 phases all the windings are used brush uses only 4 from 40 that means 10 times the power from same motor as a generator so in pm rv using multy phase brings awesome power at odd phase angles ..

THE AC INTERMITENTLY PERMUTATES THE AMPERARE 40 PHASES DIODE BRIDGE AS A NORMAL 3 PHASE BRIDGE AS 9 DEGREES PER PHASE, WYE WILL BE BETTER AS WINDINGS DO NOT INTERACT VOLTAGE DOUBLES AMPERAGE IS THE SAME REWIRED COMMUTATOR DISASSEMBLY & REWIRING ALL WIRE DISTANCES MUST BE THE SAME FOR CURRENT BALANCE EXTERNAL pm ROTOR WELL BALANCED, resists more RPM

- How can you attach the outer rotating core with any other motor? End plate V grove & belt or direct connection of rotor as END bell Other multiple ways possible using 6 segments at 120 deg to run as PM 3 PH motor - alternator genemotor (hectors original name for the RV) a true brushless AC to DC dynamotor converter (EMA type 3 converter) idea is to use as MOTOR generator Pulse motor-AC synchronous motors & other applications Vortex technology cogeneration with the RV

Statutory Public copyright (Other Rights Apply) local and international. (Publication) Scientific discovery, Rotor conversion Effect and suck-a-matron covered by the publication statutory copyrights for 75 years.

Introduction to thermodynamic heat transformation to ou regions.

To define OU = COP>1 device. A heat pumps process is an OU energy transformation in where normally there is a COP>1 where a small electricity input transforms and creates a higher heat energy output for our use. Solar cells and wind generators are COP=infinite systems, which produce electricity where we don't have to use electricity input. However, when looking it from the bigger box - we have the Sun where the energy comes from then the COP<=1. About thermodynamic conversion systems where energy is transformed from the ambient heat we can call them OU devices when we get out the useful work, heat, electricity out of it that exceeds the input. What is important is to learn to transform the energy from the available. Is it possible to take into (=suck) ambient air, put it to make work and send out cold air and power a motor or generator, can you say what normal science has to say? Is it possible to reverse the entropy? Some considerations- DEVICE 0 = heat pump (3-5x eff) + Stirling engine (30-40%) + electric generator - it is a big toy (tuned to COP>1), that will prove the concept using off-the-shelve items, but it is huge, expensive and unpractical due to the size (perhaps it won’t work as the Stirling engine requires big heat differences). Can we make a DEVICE X that can be put into the 'CAN' and do the same?

This is a very important thing here. It opens a door to a higher efficiency understanding All engineers are trained to push something, to create an energy state that is higher than environment, if they want to do/move/create something. And this procedure is programmed into their engineering curriculum. As the created energy state is higher than environment one, it is logical that a part of the input energy is used for the according task, and the rest flows into environment = losses.

Therefore you can’t reach OU that way. The concept is simple if you create an energy sink, for example as in the low pressure region in the RV-suck-a-matron, the air flows because of its own energy. Not, because the air is pushed or something, but due its own thermal energy. The air molecules are jumping into the "holes” that are created due to the Sucking.

To visualize this picture one only needs to look at what happens in a VORTEX!

Or one can also consider as does the inventor that the Air cools down due to

Expansion where it does work (not the other way around - makes work and cools down). The additional energy comes from the vortex and the vortex is powered by the gravity that adds up to the kinetic energy of the air flow.

Or by the understanding of, Let this movement do some work, and the molecules will cool down as already explained in the standard physics books describing this simple thermodynamic law. In the case of "pushing", you end up with some done work + some losses. That’s all. In the case of "vortex sucking", you end up with some done work + some losses as well +the NEXT ENERGY SINK (cold air).So, the more energy you are able to extract at sucking, the stronger is the next energy sink, which you will get.

Sucking an air acquires energy, blowing increases waste as you generate heat. So in a transformation method using the thermodynamic principle the rule is to suck and never blow in as in the Suck-a-matron system or in a turbine, chamber extraction system.

This is where E in BTU goes to a turbine as (electric) (transformed) E=e(-n) (entropy variable) were the air goes BTU - (minus) and the density goes UP were work is performed as per the standard thermodynamic law process.

The extraction system process is the vacuum pressure relative to the density of gas being extracted with a BTU negative subtracted to the vapor pressure density of gas extracted.

A laymen’s description is that it requires less energy to extract the air than the energy that is imparted from the turbine. System is an over-unity transformation engine as a tornado or hurricane...(in a can) is.