Добавил:
Andrey
Опубликованный материал нарушает ваши авторские права? Сообщите нам.
Вуз:
Предмет:
Файл:(ARM).Reference peripherals specification.pdf
X
- •Contents
- •Introduction
- •1.1 Scope
- •Figure 1-1: Main system blocks
- •1.2 Summary
- •See Chapter 2, Memory Map.
- •Level sensitive interrupts.
- •Programmed interrupt source available
- •See Chapter 3, Interrupt Controller.
- •Free-running or periodic timer modes.
- •See Chapter 4, Timer.
- •See Chapter 5, Communications Channel.
- •"Wait for Interrupt" Pause mode.
- •See Chapter 6, Remap and Pause.
- •Memory Map
- •2.1 Introduction
- •2.2 Memory Map Base Addresses
- •Interrupt Controller
- •3.1 Introduction
- •Figure 3-1: FIQ and IRQ interrupts
- •3.2 Interrupt Control
- •Figure 3-2: Interrupt Controller Bit Slice
- •3.3 Interrupt Controller Register Descriptions
- •3.5 Interrupt Controller Memory Map
- •Timer
- •4.1 Introduction
- •4.2 Timer Operation
- •Figure 4-1: Timer Block Diagram
- •Figure 4-2: Timer Pre-scale Unit
- •4.3 Timer Register Descriptions
- •4.3.1 Load Register
- •4.3.2 Value
- •4.3.3 Clear
- •4.3.4 Control Register
- •Figure 4-3: Timer Register Bit Positions
- •1—Timer Enabled
- •1—Periodic Timer Model
- •Clock
- •Divided by
- •Stages of
- •Pre-scale
- •Undefined
- •Table 4-1: Bits 3 – 2: Prescale bits
- •4.4 Timer Memory Map
- •Address
- •Read Location
- •Write Location
- •TimerBase
- •Timer1Load
- •Timer1Load
- •TimerBase + 0x04
- •Timer1Value
- •Reserved
- •TimerBase + 0x08
- •Timer1Control
- •Timer1Control
- •TimerBase + 0x0C
- •Reserved
- •Timer1Clear
- •TimerBase + 0x10
- •Reserved
- •Reserved
- •TimerBase + 0x20
- •Timer2Load
- •Timer2Load
- •TimerBase + 0x24
- •Timer2Value
- •Reserved
- •TimerBase + 0x28
- •Timer2Control
- •Timer2Control
- •TimerBase + 0x2C
- •Reserved
- •Timer2Clear
- •TimerBase + 0x30
- •Reserved
- •Reserved
- •Table 4-2: Timer Address Map
- •Communications Channel
- •5.1 Introduction
- •Remap and Pause
- •6.1 Introduction
- •6.2 Pause
- •6.4 Reset Status
- •6.5 Clear Reset Memory Map
- •6.6 Remap and Pause Memory Map
- •Address
- •Read Location
- •Write Location
- •RemapBase
- •Reserved
- •Pause
- •RemapBase + 0x10
- •Identification
- •Reserved
- •RemapBase + 0x20
- •Reserved
- •ClearResetMap
- •RemapBase + 0x30
- •ResetStatus
- •ResetStatusSet
- •RemapBase + 0x34
- •Reserved
- •ResetStatusClear
- •Table 6-1: Remap and Pause Memory Map
Introduction
1.1Scope
This specification gives a programmer's model of an ARM based system. The intention of the specification is to increase the commonality between ARM system designs and hence increase the level of software portability between systems.
The specification details the basic system elements that are replicated across most system designs. The diagram below shows the main system blocks.
Reset and Pause |
|
|
Control |
|
|
Interrupt |
ARM |
|
Processor |
||
Controller |
||
|
||
Timers |
|
Figure 1-1: Main system blocks
1-2 |
Reference Peripherals Specification |
|
|
|
ARM DDI 0062D |
|
|
|
|
|
|
Open Access
Соседние файлы в предмете Электротехника