II. General Tips

To compare cab/mics, you want a true A vs. B comparison. After you've dialed in your amp tone, picked a cab/mic, and EQ'ed the patch in pretty well, clone the patch (save it to a neighboring or empty patch space), select a different cab or mic in the clone, re-tweak the EQ and Cab DEP's, then compare the new patch vs. the original. Otherwise if you just switch the cab you're comparing, one cab is dialed in and one is not. Each cab/mic will have unique EQ and Cab DEP settings ideal to the patch you're trying to create. Compare tweaked cabs to tweaked cabs, not defaults to defaults or tweaks to defaults. Additionally, the Tread V-30 4x12 is significantly louder than any of the other cabinets, which makes it difficult to compare it to other cabs as you're trying to build a patch. Compensate your patches for volume as well as EQ differences.

A lot of the tones I seek require a nice, bright top-end. This often goes too far, putting harsh highs in the tone. But these can easily be rolled off using a Mid-Focus EQ. I stick to my general principles - that it's better to filter out frequencies than to try to dial them in and to start with the cleanest signal possible and EQ or otherwise adjust it.

But sometimes you want a cab's unique tone, and that means I may need to boost the high-end. I like to use the Studio EQ to do so - it uses wide boosts and it has an 8 kHZ selection, that allows it to focus higher than the Parametric EQ. Another good option is the Parametric EQ. Although the frequency selection only goes up to about 5 kHZ, it has a high shelf that can make a nice even boost to the highs. If this ends up putting too much crackle in the ultra-high end, again, a Mid-Focus EQ is best to roll that off.

Top of Cabs and Mics

III. Hiway 4x12

Vintage	_____*____	Modern
Dark	______*___	Bright
Midsy	__*_______	Scooped
Loose	______*___	Tight
Noisy	______*___	Hi-Fi
Thin	_____*____	Thick
Smooth	_____*____	Harsh

After testing pretty much all of the cabs in depth, EQ'ing out any sore spots that may initially overwhelm me, I came to the conclusion that the Hiway rules all other cabs in its ability to deliver the tone of a real guitar speaker. I can't say exactly what speaker it sounds like. Some of the recorded tones I've tried to emulate have used Celestion Vintage 30's, Celestion Greenbacks, and Altec 417-8H's, maybe some others as well. In all cases, I got the Hiway cab to sound more like the tone than the Tread V-30, XXL V-30, Greenbacks, or other cabs. Some tones, which I know used Vintage 30's, sound virtually identical to the tone I can get with this cab model. The actual speakers modeled in the Hiway cab are Fane 12287, which I cannot find any clips of or detailed comparison to speakers I'm more familiar with. In any case, I am currently in love with this cab model. I use it in virtually all my single-amp patches now, replacing the Tread V-30 and Greenbacks 4x12's I was using.

I'm still trying to figure out why it took me over a year to realize this about this cab, as I formerly thought the Tread V-30 cab ruled the roost. I think I was biased against it due to it being a "vintage" model, with speakers I was quite unfamiliar with. Also, the first thing you'll notice about the tone is that it's really midsy - right in the honk area of the mids, which is NOT metal. Dialing the mids out can be a little tricky, but I find a Parametric EQ with frequency at 47%, Q around 50%, and gain around 35-40% does nicely. It's the low and high-end tone that I really like here.

This cab is not perfect. It's not as loud and clear as the Tread V-30, but I think it's still preferable because the tone is so much more consistent across the entire frequency spectrum. Also, it can be a little weak on bass, which you'll have to dial in. This can lead to a bit of drone and boom in the low end, which is off-putting. But dialing in the bass isn't as noticeable, especially in a mix, as the fake or dead sound of the other cabs.

For DEP's, I like to turn the Res. Level down quite a bit in general (25%), making the tone quite crispy and clear and I boost Thump to add a bit of punch.

Top of Cabs and Mics