During the wax design fitting of the full removable denture on the upper jaw in oral cavity, at the speaker tests revealed abnormality of clearness pronunciation of the words. Defect in a pronunciation of sounds: B, P, M are present. What causes of this infringement?

The frontal upper artificial teeth are too short

The overestimated vertical size of the frontal upper artificial teeth and they are excessively pushed forward.

Too expanded form of the upper jaw tooth arch.

Distal edge of the denture basis is thin.

Patient С, 56 years, has addressed at the dental clinic with complaints on the total absence of teeth. From the anamnesis is known the allergic reaction on acril plastic mass. What denture design will be the most expedient, considering the high aesthetic requirements to design?

Complete denture with metal framework.

Complete denture is made from colourfree acril plastic basis.

Implantation with the subsequent manufacturing of the metal-ceramic denture.

The denture is made from polypropylene with ceramic teeth.

Manufacturing of full removable dentures are planned to toothless patient, 60 years old. The patient’s head hear-covering is absent, patient has moustaches and beard on the face. How to define the inter alveolar height?

By the way of anatomo-physiological method.

By the way of anthropometrical method.

The anatomic method.

By comparison of three parts of the person.

By the compass of the "golden ratio”.

Patient С, 62 years, has addressed in clinic of orthopedic dentistry concerning burning under the full removable denture which is using for 5 months. From the anamnesis it is known that the full removable denture is made for the first time. It is known also that burning under the denture basis through 10 – 15 minutes after putting on, also disappears through 20 - 30 minutes after its removal. At the objective survey of the removable denture is a satisfactory quality. At survey of oral cavity, the mucous membrane inflammation at the it’s contact place with the full removable denture is revealed. Define the most probable diagnosis of patient’s disease?

Display of diseases gastrointestinal tract

Reaction on - somatic disease

The traumatic stomatitis

The allergic stomatitis

The toxic stomatitis

At a stage of imposing of full removable denture on the lower jaw is revealed denture shift back. What is reason?

The denture basis modeling is strongly volume from it vestibular side.

Unduly volume basis modelling from tongue side

Unduly truncated denture buccal edge

Unduly truncated denture lip edge

The anterior teeth are setup with oral inclination

Patient С, complains on the bad fixation of full removable dentures, insignificant pains in TMJ aria. From the anamnesis removable denture was made 8 years ago. In what time it is necessary to replace full removable dentures ?

In 3-4 years

In 2 years

In 5 years

In 1 year

In 6 years

To patient B, 72 years, are produced full removable dentures with individual formation of occlusial planes. What factors should be considered in this case?

Sagital, but transversal phenomena of Hristensena

Size of the lower jaw corner

The geometrical form of mandibular alveolar processes

Perimeter of the lower jaw

The longitudinal and transversal sizes of the lower jaw

Full removable dentures are produced to patient,59 years old with setup of artificial teeth by individually-generated occlusal planes. What device should be applied for this purpose in this case?

Jointed оccludator

Advanced оccludator

Universal articulator

Simplified articulator

Jointless articulator

Toothless upper jaw’s patient, 65 years old has addressed at the dental clinic for the purpose of dental prosthetics. At the clinical examination has been revealed visibility mobile alveolar crest of atrophied alveolar process. What functional print should be preferred in this case?

Decompensated

Compensated

Differentiated

Full anatomic

Full anatomic under the chewing pressure

Toothless lower jaw’s patient has addressed at the dental clinic for the purpose of dental prosthetics. Objective: even high-grade atrophy of alveolar process. The alveolar arch hardly raises over the mouth floor. The frenulums attaching and folds situation are high. Mucous membrane of prosthetic area is mobile. Please, define the atrophy type of toothless lower jaw by Keller:

ІІ type

І type

ІІІ type

ІV type

In type

The patient complains on the cheek biting during chewing. From the anamnesis: 3 days ago was made full removable dentures. What error was admitted at the dentures manufacturing?

Artificial teeth was setuped without nonregistering of the muscular balance

Prothetic plane in the lateral area was constructed incorrectly

The height central occlusion was overestimated

The mucous membrane flexibility is not considered at the functional print obtaining

The height central occlusion was underestimated

The patient complains on the tiredness of chewing muscles and knock of artificial teeth during talk. From the anamnesis: one month ago full removable dentures has been made. What error is admitted at the full removable dentures manufacturing?

The height central occlusion was overestimated

The Horizontal RJ was defined incorrectly

Prothetic plane was constructed incorrectly

The height central occlusion was underestimated

Wrong statement of teeth

Full removable dentures on the upper and lower jaws are made to the patient of 66 years old man. What doctor’s manipulation should execute after the fitting tray-basis?

Definition of CRJ’s height

Lip surface formation of the lower wax roller

Prothetic plane formation

Formation of height of the upper wax roller

Lip surface formation of the upper wax roller

The patient complaints on impossibility bite of the food. From the anamnesis known, that two weeks ago have been made full removable dentures. At survey, the artificial tooth contact observed only at the lateral areas in the anterior occlusion position. What doctor’s tactics will be at that clinical situation?

To make new full removable dentures adjusted individual occlusion surfaces.

To make selective burnishing of the lateral artificial tooth

To restore frontal teeth group by means of the self-hardening plastic mass.

To wait the last adaptation period to full removable dentures.

To make new full removable dentures with the shorter dentitions.

The patient has addressed with complaints on the pain in the mucous membrane of palatal area under the basis of the removable denture which was made three months ago. Objectively: sharply expressed palatal torus, the mucous membrane in its area is hyperemic and swell. What is the most probable cause of that complication?

Torus’s isolation was not spent

The previous print was obtained by gypsum

The functional print was obtained by means rigid individual tray

Anatomic teeth’s setup was spent

The denture basis was made from the acrylic plastic

Full removable denture was made on the upper jaw to the patient. Full removable denture is dumped when the lower jaw moving out in the anterior occlusion position. At what clinical stage the error was admitted?

Check of the full removable denture design.

Individual tray’s fitting

Functional print’s obtaining

Definition of the CO

Correction of the full removable denture

Full removable dentures on the both jaws was made to the patient of 72 years old man. Objectively: RJs are orthognathic, sharply expressed upper jaw’s atrophy. How many artificial teeth is necessary to setup into the upper denture?

14 teeth

8 teeth

10 teeth

12 teeth

16 teeth

The patient complaints on impossibility of using the full lower removable denture which have been made two weeks ago. Objectively: the pointed bone crest is palpated along the alveolar process, oblique line is expressed. What is your treatment plan?

To make a denture with an elastic spacer

To make a denture with metal basis

To make a denture with the expanded borders

To make a denture from colourless plastic mass

To make a denture with the shorten borders

Manufacturing of full removable dentures are necessary to toothless patient on both jaws. It is necessary to make the individual trays for obtaining of the functional prints. What method of it manufacturing is the most exact?

By the laboratory method into flask

From the self-hardening plastic mass

From the basic plates of ACR

From the wax

From the plastic mass PS-1

The classification of functional impressions was suggested by:

Gavrilov;*

Black;

Kennedy;

Supply.

The most expedient tactics in the case of the average expression of the torus is:

To isolate the torus; *

Differential impression;

Surgical intervention;

Shortening edge of the complete dentures;

Modelling the CD with round the torus.

What measure should be taken to prevent the injury of the incisive papilla:

Modelling the CD with round the papilla;*

It’s surgical excision;

Differential impression;

It’s isolation on the model;

To cut the basis of the CD in the papilla’s area.

What self-cured resin was made specially to produce individual trays to obtain the functional impressions?

Karboplast;*

Ftorax;

Protakril-M;

Akryloxid.

The functional impression should be removed from the oral cavity in such way:

Removed entirely;*

Divided into two equal parts;

Divided into two unequal parts.

The patient complains of difficulty chewing. He used the CD. Objectively: the mucosa is thinned and atrophied over the whole surface of the prosthetic area. Alveolar process is uniformly atrophied; the palate is not high. How to obtain the functional impression in the best way?

Without loading;*

Under the chewing pressure;

Compressive;

Arbitrary.

Combined.

Patient, 65 years old, produce CD. Objectively: expressed uniform atrophy of the alveolar process of the maxilla, hard palate is flat, torus is excessively expressed, the maxillary tuberosities are atrophied, the exostoses in the area of 13 and 23 teeth, size 5x5 mm. The mucosa in the area of the torus and exostoses is thin, atrophied; at the edges of the prosthetic area it is moderately supple. What type of functional impression it is better to obtain?

Differential functional impression;

Compressive functional impression;

Decompressive functional impression;

Compressive impression under the chewing pressure.

An objective examination of the patient’s oral cavity: the edentulous lower jaw with irregular atrophy of the alveolar process and movable alveolar ridge in the frontal area. What method of obtaining the functional impression is the best in this case?