Хорошев / ИЛП_материал_маг_02.15 / Спецификация AECMA Specification 2000M / MIL-STD-1388-2B

MIL-STD-1388-2B

APPENDIX E

A code which indicates physical and chemical characteristics of an item and identifies weight/fragility and preservative relative to the packaging of an item. For applicable codes, see MIL-STD-2073-1 and MIL-STD-2073-2.

A series of codes which identify packing requirements. Consists of the following subfields:

A code assigned to identify minimum packing requirements. For applicable codes, see MIL-STD-2073-1 and MIL-STD-2073-2.

A field divided into nine subfields which describes technical capabilities/characteristics that an item of operational equipment, TMDE, or calibration equipment/standard is capable of measuring/generating, or which are to be measured on the UUT. Classified parameters and transistor logic levels are not listed in the CMRS. Classified parameters are listed in a classified supplement or appendix to the CMRS and that document appropriately controlled.

A two character code linking the requirements set by the unit under test to the capabilities of the SE.

SE PARAMETER GROUP CODE. A PGC of the SE.

SE UUT PARAMETER GROUP CODE. A PGC of the SE UUT which must match the PGC of the corresponding SE.

UUT PARAMETER GROUP CODE. A PGC of the unit under test (WT) which must match the PGC of the corresponding SE.

question (SE or UUT) as an input into equipment or output from the equipment. Codes are as follows:

- 481 -

is capable of measuring or which are to be measured on the WT.

SE UUT PARAMETER. A parameter of the SE UUT which requires measurement by the SE under analysis.

SUPPORT EQUIPMENT PARAMETER. A parameter which the SE under analysis is to measure.

UUT PARAMETER. A parameter of the SE UUT which requires measurement by the SE under analysis.

The lowest value of a particular parameter which can be measured or generated.

SE UUT PARAMETER RANGE FROM. The lowest value of the parameter of the SE UUT that the SE under analysis must measure.

SUPPORT EQUIPMENT PARAMETER RANGE FROM. The lowest value of the parameter that the SE is capable of measuring.

UUT PARAMETER RANGE FROM. The lowest value of the parameter of the UUT that the SE under analysis must measure,

The highest value of a particular parameter which can be measured or generated.

SE UUT PARAMETER RANGE TO. The highest value of the parameter of the SE UUT that the SE under analysis must measure.

SUPPORT EQUIPMENT PARAMETER RANGE TO. The highest value of the parameter that the SE is capable of measuring.

UUT PARAMETER RANGE TO. The highest value of the parameter of the UUT that the support equipment under analysis must measure.

A narrative description of the tolerances of the corresponding parameter.

- 482 -

MIL-STD-1388-2B

APPENDIX E

SE UUT PARAMETER ACCURACY. The amount of accuracy of the parameter of the SE UUT that the SE under analysis must measure.

SUPPORT EQUIPMENT PARAMETER ACCURACY. The amount of accuracy of the parameter that the SE is capable of measuring.

UUT PARAMETER ACCURACY. The amount of accuracy of the parameter of the UUT that the support equipment under analysis must measure.

A code used to identify specific parameters as either a “range” or a specific “value”. List specific value parameters in the ‘Range-From” block.

SUPPORT EQUIPMENT PARAMETER RANGE/VALUE CODE. The R/V of the SE.

UUT PARAMETER RANGE/VALUE. The R/V of the UUT.

A code indicating whether the associated parameter is operational or specification parameter of the UUT.

The cost added to items bought by a prime contractor which are delivered to the government with little or no value added by the prime contractor.

The percentage of all corrective maintenance actions that can be accomplished within a specified maximum time to repair.

MAINTENANCE LEVEL PERCENTILE. The percentile within the specified maximum time to repair for a given operations/maintenance level.

REQUIRED PERCENTILE. The percentile associated with the requirement maximum time to repair.

Signifies when the following performance standards are required for an individual task.

- 483 -

MIL-STD-1388-2B

A three-position code identifying each person required to perform the subtask (codes “A” through “999”). Within a task, a given Person ID relates to a specific “Job” and a specific Skill Specialty Code.

A narrative description identifying any unique physical or mental personnel attributes required or recommended as prerequisites to full qualification in the applicable task.

A code which indicates the security classification or pilferage control for physical assets. For applicable codes, see DOD 4100.38-M.

A code indicating selection status of certain complex assemblies/ components considered for pilot rework/overhaul (PR/O) as part of the preoperational support program.

Items nominated are those which require additional skills, training, support and test equipment, facilities, and technical data to ensure a rework/overhaul capacity concurrent with government support of the end item. Consideration shall be given to both intermediate rework and depot level overhaul items.

- 484 -

MIL-STD-1388-2B

APPENDIX E

A code which indicates the amount and type of precious metal contained in a specific reference numbered item. For applicable codes, see DOD 4100.38-M.

The name of the activity preparing SE data.

A code which indicates the material used to prevent or inhibit corrosion or deterioration of an item. For applicable codes, see MIL-STD-2073 series.

A code which indicates whether or not the task code is applicable to the PMCS tables.

The PLISN which appeared on the Interim Support Items List, the Long Lead Times Items List, or first appearance of item in incremental pro visioing submittals.

The computed or expected time interval in months between placement of a new contract and shipment of the first deliverable quantity.

This factor is used to account for nonproductive time and has the effect of increasing manpower requirements for performing maintenance. For instance, if the soldier’s scheduled work day is 8 hours, he may only be available for 6 hours to do maintenance due to other duty assignments, in this case, the productivity factor is ((8-6)/8) + 1 = 1.25.

- 485 -

MIL-STD-1388-2B

APPENDIX E

A code indicating whether the part is included within contractually controlled Federal Supply Classes (FSC), as outlined in MIL-STD-965, Parts Control Program. Codes assigned are as follows:

A government code to identify the service supporting Inventory Control Point (ICP) where the using SE weapon/inventory manager is located. Codes are as follows:

The proper shipping name of the item to be transported, if this name is categorized as a hazardous material (e.g., CFR 49, UNTDF).

- 486 -

MIL-STD-1388-2B

APPENDIX E

The ELIN which was assigned to the previous item procurement on an item affected by proration,

The specific quantity remaining on order for the Prorated Exhibit Line Item Number.

A number assigned by the requiring authority to identify a specific contract or a group of end items/components that can have many configurations/models.

NOTE: The first position shall be alphabetic and will identify the applicable military service/agency provisioning designator having responsibility for the item(s) being processed.

A code which indicates whether the item is documented on another list or is a government furnished item.

- 487 -

MIL-STD-1388-2B

APPENDIX E

A sequentically assigned value for all items contained in the system/ equipment breakdown. The codes are as follows:

AAAA through 9999 (less I and O)

The numbering of line items shall begin with AAAA and progress through 9999, or as specified by the requiring authority.

a. When an item is contained in both a common and bulk items list (CBIL and a provisioning parts list (PPL), it may be assigned the same PLISN on both lists. When an item appears on a CBIL only, the PLISN may be unique (i.e., will not duplicate any PLISN in the PPL).

b. The fifth position of the PLISN shall be used to indicate addi tions to the breakdown. For this purpose, the letters A through Z, inclusive (except I and O) and the numbers O through 9, inclusive, shall be used starting with the letter A for the first addition and continuing sequentially through the alphabet and then through the numeric characters. An add entry, identified by the letters A, B, C, etc. , in the fifth position of the PLISN, is sequenced for inserting new items in the provisioning list either as a first or subsequent (same as) item en-

SYSTEM/EI PROVISIONING LIST ITEM SEQUENCE NUMBER. The PLISN of the system/end item as a model (A indenture code) item.

A description in narrative form used to provide additional identification of an item to be included in a repair parts manual.

A code which indicates that an item is to be selected for a specific provisioning technical documentation list. If the item applies to a particular list, a “Y” is entered. Leave blank if the item does not apply. The lists for which items can be selected are as follows:

- 488 -

—Note: Design Change Notice processing occurs against an established list (normally the PPL or PCL).

A code used to indicate the Unit of Measure (UM) or Unit of Issue (UI) Price, which will be used for provisioning technical documentation, when multiple UM PRICES are entered.

UI PRICE PROVISIONING. The provisioning UI price.

UM PRICE PROVISIONING. The provisioning UM price.

FAIL SAFE, ENVIRONMENTAL, ETC.

A narrative description identifying maintainability design constraints and characteristics that must be considered during the design process, to include:

- 489 -

MIL-STD-1388-2B

APPENDIX E

a.Fail Safe Requirements. A narrative description identifying

required fail safe characteristics (i.e., redundancy) back-up systems, built-in-test and warning equipment, fail safe provisions necessary to protect the equipment from serious damage after failure, and design features to prevent injury to personnel Subsequent to equipment failure).

b.Environmental Considerations. A narrative description identify

ing the applicable environmental conditions within which the item can operate satisfactorily. This information should include limitations, sensitivity factors, etc. , that can affect the performance and

reliability of the item installed in the system/equipment. Limiting fac- tors such as the following should be considered: shock limits; vibration

limits; ambient temperature ranges; operating temperatures in area (compartment) where item is installed in the system/equipment; humidity factors; altitude factors; magnetic interference; dust and dirt factors; salts or other corrosive atmosphere; and, light sensitivity. The narra- tive should include that portion of the system/equipment environmental impact statement which relates to the effects of the support system on the environment.

c. Nuclear Hardened Characteristics. A narrative description identifying the design characteristics which provide minimum nuclear survivability of the item. No design changes should be made without survivability/vulnerability evaluation to avoid inadvertent degradation of nuclear hardness.

The total number of times a line item is used in the assembly of which it is a part. If the quantity is unknown or cannot be determined, specify the quantity by “V” (variable) or as specified by the provisioning activity.

Option 1. The contractor shall enter the total number of times the

by individual piece parts at its first appearance, the quantity for the

Option 3. The contractor shall enter the total number of times the line item is used in the assembly of which it is a part. An assembly only. needs to be broken out to its piece parts at its first occurrence on a list. Subsequent appearances of the same assembly shall not be broken out.

- 490 -