WHEEL OPENING AND BODY SIDE MOULDING REMOVAL AND INSTALLATION (FIG. 38)

FRONT FENDER

(1)Remove screws holding wheel opening moulding to front fender.

(2)Pry bottom of body side moulding from clip on front fender using a suitable trim stick. Lift moulding from clip and separate from fender.

(3)Replace damaged moulding clip weld studs with repair screws. Paint bare metal surfaces behind moulding to avoid rust.

(4)Position moulding in wheel opening and start top center screw of wheel opening moulding.

(5)Hook top of body side moulding over clip and snap bottom of moulding onto clip.

(6)Install screws around wheel opening.

DOORS

(1)Pry bottom of body side moulding from clips on door using a suitable trim stick. Lift moulding from clip and separate from door.

(2)Replace damaged moulding clip weld studs with repair screws. Paint or undercoat bare metal surfaces behind moulding to avoid rust.

(3)Position moulding on door in design location.

(4)Hook top of moulding over clips and snap bottom of moulding onto clips.

QUARTER PANEL

(1)Remove screws holding wheel opening moulding to quarter panel.

(2)Pry bottom of body side moulding from clip on quarter panel using a suitable trim stick. Lift moulding from clip and separate from fender.

(3)Replace damaged moulding clip weld studs with repair screws. Paint or undercoat bare metal surfaces behind moulding to avoid rust.

(4)Position moulding in wheel opening and start top center screw of wheel opening moulding.

(5)Hook top of body side moulding over clip and snap bottom of moulding onto clip.

(6)Install screws around wheel opening.

APPLIQUE MOULDING AND RETAINER REMOVAL (FIG. 38)

(1)Remove screws holding applique to rocker panel from under vehicle.

(2)Lift applique upward to separate from retaining channel.

(3)Remove pop-rivets holding retainer to rocker panel using a suitable drill.

APPLIQUE MOULDING AND RETAINER INSTALLATION

(1) Install applique retainer on rocker panel with pop-rivets. Paint or undercoat bare metal surfaces to avoid rust.

(2) Hook top of applique over retainer channel and install screws under rocker panel.

COWL PANEL TRIM AND SCUFF PLATES

COWL PANEL AND DOOR OPENING SCUFF PLATE REMOVAL (FIG. 39)

(1)Open front door.

(2)Remove screw holding trim panel to cowl forward of the front door opening.

(3)Remove screws holding scuff plate to door sill.

(4)Separate cowl panel trim and scuff plate from vehicle.

COWL PANEL AND DOOR OPENING SCUFF PLATE INSTALLATION

Reverse the preceding operation.

REAR DOOR OPENING SCUFF PLATE REMOVAL (FIG. 39)

(1)Open rear door.

(2)Remove screws holding scuff plate to door sill.

(3)Separate scuff plate from vehicle.

REAR DOOR OPENING SCUFF PLATE INSTALLATION

Reverse the preceding operation.

A-PILLAR AND ROOF RAIL MOULDINGS

A-PILLAR MOULDING REMOVAL (FIG. 39)

(1)Open front door.

(2)Disengage clips holding A-pillar moulding to roof rail above door opening.

(3)Slide A-pillar moulding upward and pull rearward to separate moulding from A-pillar.

A-PILLAR MOULDING INSTALLATION

Reverse the preceding operation.

REAR DOOR ROOF RAIL MOULDING REMOVAL (FIG. 39)

(1)Open rear door.

(2)Disengage clips holding roof rail moulding to roof rail above rear door opening.

(3)Separate moulding from vehicle.

REAR DOOR ROOF RAIL MOULDING INSTALLATION

Reverse the preceding operation.

B-PILLAR TRIM PANEL

B-PILLAR TRIM PANEL REMOVAL (FIG. 39)

(1)Remove roof rail mouldings and scuff plates as necessary.

(2)Remove shoulder harness turning loop cover. Remove bolt holding turning loop to B-pillar.