Ä |
|
IGNITION SYSTEMS 8D - 41 |
|
||
|
TURBO III, 3.3L AND 3.8L IGNITION SYSTEMSÐSERVICE PROCEDURES |
|
|
INDEX |
|
|
page |
Camshaft Sensor ServiceÐTurbo III Engine |
. . . . . 46 |
Camshaft SensorÐ3.3L and 3.8L Engines . |
. . . . . 46 |
Coolant Temperature SensorÐ3.3L and |
|
3.8L Engines . . . . . . . . . . . . . . . . . . . . . . |
. . . . . 41 |
Coolant Temperature SensorÐTurbo III . . . |
. . . . . 41 |
Crankshaft SensorÐ3.3L and 3.8L Engines |
. . . . . 45 |
Crankshaft SensorÐTurbo III Engine . . . . . . |
. . . . 45 |
Detonation (Knock) SensorÐTurbo III Engines |
. . . 42 |
Engine Controller . . . . . . . . . . . . . . . . . . . . . |
. . . . 41 |
ENGINE CONTROLLER
REMOVAL
(1)Remove air cleaner duct or air cleaner assembly.
(2)Remove battery.
(3)Remove engine controller mounting screws (Fig.
1).
(4)Remove 60-way connector from engine controller. Remove controller.
Fig. 1 Removing the Engine Controller
INSTALLATION
(1)Connect 60-Way connector to engine controller (Fig. 1).
(2)Install Engine Controller on inside left front fender. Install and tighten mounting screws.
(3)Install the battery.
(4)Install air cleaner duct or air cleaner assembly.
COOLANT TEMPERATURE SENSORÐTURBO III
The coolant sensor threads into the thermostat housing (Fig. 2).
|
page |
Idle RPM Test . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 43 |
Ignition Coil ServiceÐTurbo III Engine . . . . . . . . |
. 47 |
Ignition CoilÐ3.3L and 3.8L Engine . . . . . . . . . . |
. 47 |
Manifold Absolute Pressure (MAP) SensorÐ3.3L |
|
and 3.8L Engines . . . . . . . . . . . . . . . . . . . . . . |
. 47 |
Manifold Absolute Pressure (MAP) SensorÐ |
|
Turbo III Engine . . . . . . . . . . . . . . . . . . . . . . . |
. 47 |
Spark Plug Cable Service . . . . . . . . . . . . . . . . . . |
. 42 |
Spark Plug Service . . . . . . . . . . . . . . . . . . . . . . |
. 43 |
REMOVAL
(1)Drain cooling system until coolant level is below thermostat housing. Refer to Group 7, Cooling System.
(2)Remove air cleaner fresh air duct.
(3)Disconnect electrical connector from coolant sensor.
(4)Remove sensor from thermostat housing (Fig.
2).
Fig. 2 Coolant Temperature SensorÐTurbo III
INSTALLATION
(1)Install sensor. Tighten to 7 NIm (60 in. lbs.) torque.
(2)Connect electrical connector to coolant sensor
(3)Fill cooling system. Refer to Group 7, Cooling System.
(4)Install fresh air duct.
COOLANT TEMPERATURE SENSORÐ3.3L AND 3.8L ENGINES
The coolant temperature sensor is located below the ignition coil (Fig. 3).