10.8 Chapter Quiz

10.8.1 Chapter Quiz Page 1:

10.8.1 - Chapter Quiz 1.Determine the IP addresses that are usable for hosts on the subnetworks of the 200.100.50.0/28 network.  Addresses:  200.100.50.25  200.100.50.80  200.100.50.100  200.100.50.143  200.100.50.208  200.100.50.170  200.100.50.90  200.100.50.79  Categories:  Usable for host address  Not usable for host address  2.When is a straight-through cable used in a network?  A.When connecting a router through the console port  B.When connecting one switch to another switch  C.When connecting a host to a switch  D.When connecting a router to another router  3.Refer to the topology description below to answer the question.  Topology description:  Router R1 is connected to a CSU/DSU. The CSU/DSU is connected to one side of a network cloud. Router R2 is connected to another CSU/DSU. This CSU/DSU is connected to the opposite side of the network cloud.  Which function is a unique responsibility of the DCE devices shown in the exhibit?  A.Transmission of data  B.Reception of data  C.Clocking for the synchronous link  D.Noise cancellation in transmitted data  4.A router that terminates a serial WAN link is typically a D T E device. Under which circumstance would a router be configured as a DCE device?  A.A router cannot be configured as a DCE device.  B.When connecting a router directly to an analog device.  C.When performing a back-to-back router scenario in a test environment.  D.When the clock rate from the service provider cannot be matched by the router.  5.Which of the following are private IP addresses? (Choose three.)  A.10.1.1.1  B.172.32.5.2  C.192.167.10.10  D.172.16.4.4  E.192.168.5.5  F.224.6.6.6  6.Match the slash-format prefix number with the decimal mask number to subnet the last octet.  Slash-format prefix numbers:  /24  /25  /26  /27  /28  /29  /30  Decimal mask numbers:  128  252  224  0  248  192  240  7.Refer to the topology description to answer the question.  Topology description.  Router R1 interface FA0 is connected to router R2 interface FA0.  What type of cable connects the two routers together without any intermediary device?  A.Console  B.Rollover  C.Crossover  D.Straight-through  8.When setting the COM port properties for a PC, which option defines the default port configuration settings used to establish a direct serial connection between a computer and a Cisco networking device?  A.19,200 bps, 8 data bits, no parity, 1 stop bit, no flow control  B.9600 bps, 8 data bits, even parity, 2 stop bits, hardware flow control  C.9600 bps, 16 data bits, odd parity, 1 stop bit, hardware flow control  D.19,200 bps, 8 data bits, even parity, 1 stop bit, hardware flow control  E.9600 bps, 8 data bits, no parity, 1 stop bit, no flow control  9.Which three UTP cable lengths are specified by ANSI/T IA/EIA-568-B standards? (Choose three.)  A.Total end-to-end length of up to 100 meters  B.Up to 110 meters total end-to-end length  C.Horizontal cabling maximum of 90 meters  D.Up to 10 meters for interconnecting patch panels  E.Up to 5 meters for interconnecting patch panels  F.Up to 10 meters for connecting individual devices to wall jacks  10.What primary factor should be addressed before using wireless technology?  A.FFC address assignment  B.Selecting an Auto-MDIX capable switch  C.Power supply redundancy  D.Identify and if possible minimize sources of RFI