Добавил:

Upload Опубликованный материал нарушает ваши авторские права? Сообщите нам.

Вуз:

Национальный университет Львовская политехника

Предмет:

[НЕСОРТИРОВАННОЕ]

Файл:

smccp

.pdf

Скачиваний:

Добавлен:

12.02.2016

Размер:

1.75 Mб

Скачать

☆

<<< < Предыдущая 1 23 / 103 4 5 6 7 8 9 10 > Следующая >>>

X7S Dielectric

General Specifications

GENERAL DESCRIPTION

X7S formulations are called “temperature stable” ceramics and fall into EIA Class II materials. Its temperature variation of capacitance is within ±22% from –55°C to +125°C. This capacitance change is non-linear.

Capacitance for X7S varies under the influence of electrical operating conditions such as voltage and frequency.

X7S dielectric chip usage covers the broad spectrum of industrial applications where known changes in capacitance due to applied voltages are acceptable.

PART NUMBER (see page 2 for complete part number explanation)

1206

105

Size

Voltage

Dielectric

Capacitance

Failure

Terminations

Packaging

Special

(L" x W")

4 = 4V

Z = X7S

Code (In pF)

Tolerance

Rate

Code

T = Plated Ni

= 7" Reel

= 6.3V

2 Sig. Digits +

K = ±10%

A = N/A

and Sn

= 13" Reel

A = Std.

Z = 10V

Number of

M = ±20%

= Bulk Cass.

Product

Y = 16V

Zeros

= 25V

= 50V

1 = 100V

2 = 200V

NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers.

TYPICAL ELECTRICAL CHARACTERISTICS

				X7S Dielectric
		Typical Temperature Coefficient							Capacitance vs. Frequency
									Capacitance vs. Frequency
	10							+30
	10							+30
	5						Capacitance	+20
	5
ChangeCap%	0
ChangeCap%								+10

	-5

								0

	-10
	-10							-10
	-15						%
	-15
	-20							-20


	-25
	-25
	-60 -40 -20			0 20 40 60 80	100 120 140			-30
	-60 -40 -20			0 20 40 60 80	100 120 140			-30			10 KHz			100 KHz		1 MHz	10 MHz
				Temperature (°C)				1KHz			10 KHz			100 KHz		1 MHz	10 MHz
				Temperature (°C)									Frequency
													Frequency
	Variation of Impedance with Cap Value							Variation of Impedance with Chip Size
			Impedance vs. Frequency					Variation of Impedance with Chip Size
			1,000 pF vs. 10,000 pF - X7S							Impedance vs. Frequency
				0805								10,000 pF - X7S
	10.00							10
	10.00					1,000 pF		10							1206
															1206
															0805
															0805
						10,000 pF									1210
	1.00							1.0
Impedance,	1.00						Impedance,	1.0
Impedance,	0.10						Impedance,	0.1
	0.10							0.1
	0.01							.01
	0.01							.01
	10			100	1000			1					10		100		1,000
				Frequency, MHz									Frequency, MHz

Farads)-(Ohm	1,000	Insulation Resistance vs Temperature
Resistance	10,000
	100










Insulation
	0







			20	40		60	80	100	120
	0		20	40		60	80	100	120
					Temperature °C
	Variation of Impedance with Chip Size
			Impedance vs. Frequency
				100,000 pF - X7S
	10						1206
							1206
							0805
							1210
	1.0
Impedance,

	0.1
	0.1
	.01
	.01
	1			10			100		1,000

Frequency, MHz

X7S Dielectric

Specifications and Test Methods

Parameter/Test		X7S Specification Limits	Measuring Conditions
Operating Temperature Range		-55ºC to +125ºC	Temperature Cycle Chamber
Capacitance		Within specified tolerance
		≤ 2.5% for ≥ 50V DC rating	Freq.: 1.0 kHz ± 10%
Dissipation Factor		≤ 3.0% for 25V DC rating	Voltage: 1.0Vrms ± .2V
Dissipation Factor		≤ 3.5% for 16V DC rating	For Cap > 10 μF, 0.5Vrms @ 120Hz
		≤ 3.5% for 16V DC rating	For Cap > 10 μF, 0.5Vrms @ 120Hz
		≤ 5.0% for ≤ 10V DC rating
Insulation Resistance		100,000MΩ or 1000MΩ - μF,	Charge device with rated voltage for
Insulation Resistance		whichever is less	120 ± 5 secs @ room temp/humidity
		whichever is less	120 ± 5 secs @ room temp/humidity
Dielectric Strength			Charge device with 300% of rated voltage for
Dielectric Strength		No breakdown or visual defects	1-5 seconds, w/charge and discharge current
			limited to 50 mA (max)
	Appearance	No defects	Deflection: 2mm
Resistance to	Capacitance	≤ ±12%	Test Time: 30 seconds
	Variation	≤ ±12%	1mm/sec
	Variation		1mm/sec
Flexure	Dissipation	Meets Initial Values (As Above)
Stresses	Factor	Meets Initial Values (As Above)
Stresses	Factor
	Insulation	≥ Initial Value x 0.3	90 mm
	Resistance	≥ Initial Value x 0.3	90 mm
	Resistance

Solderability		≥ 95% of each terminal should be covered	Dip device in eutectic solder at 230 ± 5ºC
Solderability		with fresh solder	for 5.0 ± 0.5 seconds
		with fresh solder	for 5.0 ± 0.5 seconds
	Appearance	No defects, <25% leaching of either end terminal
	Capacitance	≤ ±7.5%
	Variation	≤ ±7.5%	Dip device in eutectic solder at 260ºC for 60
	Variation
	Dissipation
Resistance to	Dissipation	Meets Initial Values (As Above)	seconds. Store at room temperature for 24 ± 2
Resistance to	Factor	Meets Initial Values (As Above)	seconds. Store at room temperature for 24 ± 2
Solder Heat	Factor		hours before measuring electrical properties.
Solder Heat	Insulation	Meets Initial Values (As Above)	hours before measuring electrical properties.
	Insulation
	Resistance
	Resistance
	Dielectric	Meets Initial Values (As Above)
	Strength	Meets Initial Values (As Above)
	Strength
	Appearance	No visual defects	Step 1: -55ºC ± 2º	30 ± 3 minutes
	Capacitance	≤ ±7.5%	Step 2: Room Temp	≤ 3 minutes
	Variation	≤ ±7.5%	Step 2: Room Temp	≤ 3 minutes
	Variation
Thermal	Dissipation	Meets Initial Values (As Above)	Step 3: +125ºC ± 2º	30 ± 3 minutes
Thermal	Factor	Meets Initial Values (As Above)	Step 3: +125ºC ± 2º	30 ± 3 minutes
Shock	Factor
Shock	Insulation	Meets Initial Values (As Above)	Step 4: Room Temp	≤ 3 minutes
	Insulation
	Resistance
	Resistance
	Dielectric	Meets Initial Values (As Above)	Repeat for 5 cycles and measure after
	Strength	Meets Initial Values (As Above)	24 ± 2 hours at room temperature
	Strength		24 ± 2 hours at room temperature
	Appearance	No visual defects	Charge device with 1.5 rated voltage (≤ 10V) in
	Capacitance	≤ ±12.5%	Charge device with 1.5 rated voltage (≤ 10V) in
	Variation	≤ ±12.5%	test chamber set at 125ºC ± 2ºC
	Variation		test chamber set at 125ºC ± 2ºC
Load Life	Dissipation	≤ Initial Value x 2.0 (See Above)	for 1000 hours (+48, -0)
	Factor	≤ Initial Value x 2.0 (See Above)
	Factor		Remove from test chamber and stabilize
	Insulation	≥ Initial Value x 0.3 (See Above)	Remove from test chamber and stabilize
	Resistance	≥ Initial Value x 0.3 (See Above)	at room temperature for 24 ± 2 hours
	Resistance		at room temperature for 24 ± 2 hours
	Dielectric	Meets Initial Values (As Above)	before measuring.
	Strength	Meets Initial Values (As Above)
	Strength
	Appearance	No visual defects	Store in a test chamber set at 85ºC ± 2ºC/
	Capacitance	≤ ±12.5%	Store in a test chamber set at 85ºC ± 2ºC/
	Capacitance		85% ± 5% relative humidity for 1000 hours
	Variation		85% ± 5% relative humidity for 1000 hours
Load	Variation		(+48, -0) with rated voltage applied.
	Dissipation	≤ Initial Value x 2.0 (See Above)	(+48, -0) with rated voltage applied.
	Dissipation
Humidity	Factor		Remove from chamber and stabilize at
Humidity	Factor
	Insulation
	Insulation	≥ Initial Value x 0.3 (See Above)	room temperature and humidity for
	Resistance	≥ Initial Value x 0.3 (See Above)	room temperature and humidity for
	Resistance		24 ± 2 hours before measuring.
	Dielectric	Meets Initial Values (As Above)	24 ± 2 hours before measuring.
	Dielectric
	Strength
	Strength

X7S Dielectric

Capacitance Range

PREFERRED SIZES ARE SHADED

	SIZE
	Soldering
	Packaging
(L)	Length	MM
(L)	Length	(in.)
		(in.)
(W) Width		MM
(W) Width		(in.)
		(in.)
(t)	Terminal	MM
(t)	Terminal	(in.)
		(in.)
		WVDC
	Cap	100
	(pF)	150
		220
		330
		470
		680
		1000
		1500
		2200
		3300
		4700
		6800
	Cap	0.010
	(μF	0.015
		0.022
		0.033
		0.047
		0.068
		0.10

0.15

0.22

0.33

0.47

0.68

1.0

1.5

2.2

3.3

4.7

100

WVDC

SIZE

0402		0603		0805		1206					1210
Reflow Only		Reflow Only		Reflow/Wave		Reflow/Wave				Reflow Only
All Paper		All Paper		Paper/Embossed		Paper/Embossed				Paper/Embossed
1.00	± 0.10	1.60	± 0.15	2.01	± 0.20	3.20	± 0.20			3.20		± 0.20
(0.040	± 0.004)	(0.063	± 0.006)	(0.079	± 0.008)	(0.126	± 0.008)			(0.126		± 0.008)
0.50	± 0.10	0.81	± 0.15	1.25	± 0.20	1.60	± 0.20			2.50		± 0.20
(0.020	± 0.004)	(0.032	± 0.006)	(0.049	± 0.008)	(0.063	± 0.008)			(0.098		± 0.008)
0.25	± 0.15	0.35	± 0.15	0.50	± 0.25	0.50	± 0.25			0.50		± 0.25
(0.010	± 0.006)	(0.014	± 0.006)	(0.020	± 0.010)	(0.020	± 0.010)			(0.020		± 0.010)
	6.3	6.3	25		4	6.3		10			6.3

											W
								L			W



													T




									t


C
C
C
C

			G
	G
	G
	G
	G
				N	Q
				N	Q
				N	Q
				N	Q	Q

							Z
6.3	6.3	25		4	6.3	10	6.3
0402		0603		0805	1206		1210

Letter	A	C	E	G	J	K	M	N	P	Q	X	Y	Z
Max.	0.33	0.56	0.71	0.90	0.94	1.02	1.27	1.40	1.52	1.78	2.29	2.54	2.79
Thickness	(0.013)	(0.022)	(0.028)	(0.035)	(0.037)	(0.040)	(0.050)	(0.055)	(0.060)	(0.070)	(0.090)	(0.100)	(0.110)
			PAPER						EMBOSSED

X5R Dielectric

General Specifications

GENERAL DESCRIPTION

•General Purpose Dielectric for Ceramic Capacitors

•EIA Class II Dielectric

•Temperature variation of capacitance is within ±15% from -55°C to +85°C

•Well suited for decoupling and filtering applications

•Available in High Capacitance values (up to 100μF)

PART NUMBER (see page 2 for complete part number explanation)

1210

107

Size

Voltage

Dielectric

Capacitance

Failure

Terminations

Packaging

Special

(L" x W")

= 4V

D = X5R

Code (In pF)

Tolerance

Rate

Code

T = Plated Ni

= 7" Reel

= 6.3V

2 Sig. Digits +

K = ±10%

A = N/A

and Sn

= 13" Reel

A = Std.

= 10V

Number of

M = ±20%

= Bulk Cass.

Y = 16V

Zeros

= Bulk

= 25V

= 35V

= 50V

NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values.

TYPICAL ELECTRICAL CHARACTERISTICS

Temperature Coefficient

	20
	20
	15
	15
Capacitance	10
	10
	-5
	5
	0
	-10

%
%
	-15
	-15
	-20
	-20

-60 -40 -20

0 +20 +40 +60 +80

Temperature °C

Insulation Resistance (Ohm-Farads)

Insulation Resistance vs Temperature

10,000

1,000

100

0	20	40	60	80	100	120
0

Temperature °C

X5R Dielectric

Specifications and Test Methods

Parameter/Test

X5R Specification Limits

Measuring Conditions

Operating Temperature Range

-55ºC to +85ºC

Temperature Cycle Chamber

Capacitance

Within specified tolerance

Freq.: 1.0 kHz ± 10%

≤ 2.5% for ≥ 50V DC rating

Dissipation Factor

≤ 3.0% for 25V DC rating

Voltage: 1.0Vrms ± .2V

≤ 12.5% Max. for 16V DC rating and lower

For Cap > 10 μF, 0.5Vrms @ 120Hz

Contact Factory for DF by PN

Insulation Resistance

100,000MΩ or 500MΩ - μF,

Charge device with rated voltage for

whichever is less

120 ± 5 secs @ room temp/humidity

Dielectric Strength

Charge device with 300% of rated voltage for

No breakdown or visual defects

1-5 seconds, w/charge and discharge current

limited to 50 mA (max)

Appearance

No defects

Deflection: 2mm

Resistance to

Capacitance

≤ ±12%

Test Time: 30 seconds

Variation

1mm/sec

Flexure

Dissipation

Meets Initial Values (As Above)

Stresses

Factor

Insulation

≥ Initial Value x 0.3

90 mm

Resistance

Solderability

≥ 95% of each terminal should be covered

Dip device in eutectic solder at 230 ± 5ºC

with fresh solder

for 5.0 ± 0.5 seconds

Appearance

No defects, <25% leaching of either end terminal

Capacitance

≤ ±7.5%

Variation

Dip device in eutectic solder at 260ºC for 60

Dissipation

Resistance to

Meets Initial Values (As Above)

seconds. Store at room temperature for 24 ± 2

Factor

Solder Heat

hours before measuring electrical properties.

Insulation

Meets Initial Values (As Above)

Resistance

Dielectric

Meets Initial Values (As Above)

Strength

Appearance

No visual defects

Step 1: -55ºC ± 2º

30 ± 3 minutes

Capacitance

≤ ±7.5%

Step 2: Room Temp

≤ 3 minutes

Variation

Thermal

Dissipation

Meets Initial Values (As Above)

Step 3: +85ºC ± 2º

30 ± 3 minutes

Factor

Shock

Insulation

Meets Initial Values (As Above)

Step 4: Room Temp

≤ 3 minutes

Resistance

Dielectric

Meets Initial Values (As Above)

Repeat for 5 cycles and measure after

Strength

24 ± 2 hours at room temperature

Appearance

No visual defects

Charge device with 1.5X rated voltage in

Capacitance

≤ ±12.5%

test chamber set at 85ºC ± 2ºC for 1000 hours

Variation

(+48, -0). Note: Contact factory for *optional

Dissipation

≤ Initial Value x 2.0 (See Above)

specification part numbers that are tested at

Load Life

Factor

< 1.5X rated voltage.

Insulation

≥ Initial Value x 0.3 (See Above)

Remove from test chamber and stabilize

Resistance

Dielectric

Meets Initial Values (As Above)

at room temperature for 24 ± 2 hours

Strength

before measuring.

Appearance

No visual defects

Store in a test chamber set at 85ºC ± 2ºC/

Capacitance

≤ ±12.5%

85% ± 5% relative humidity for 1000 hours

Variation

Load

(+48, -0) with rated voltage applied.

Dissipation

≤ Initial Value x 2.0 (See Above)

Humidity

Factor

Remove from chamber and stabilize at

Insulation

≥ Initial Value x 0.3 (See Above)

room temperature and humidity for

Resistance

24 ± 2 hours before measuring.

Dielectric

Meets Initial Values (As Above)

Strength

X5R Dielectric

Capacitance Range

PREFERRED SIZES ARE SHADED

SIZE

0201

0402

0603

0805

1206

1210

1812

Soldering

Reflow Only

Reflow/Wave

Reflow Only

Packaging

All Paper

Paper/Embossed

All Embossed

(L)

Length

0.60 ± 0.03

1.00 ± 0.10

1.60 ± 0.15

2.01 ± 0.20

3.20 ± 0.20

4.50 ± 0.30

(in.)

(0.024 ± 0.001)

(0.040 ± 0.004)

(0.063 ± 0.006)

(0.079 ± 0.008)

(0.126 ± 0.008)

(0.177 ± 0.012)

(W) Width

0.30 ± 0.03

0.50 ± 0.10

0.81 ± 0.15

1.25 ± 0.20

1.60 ± 0.20

2.50 ± 0.20

3.20 ± 0.20

(in.)

(0.011 ± 0.001)

(0.020 ± 0.004)

(0.032 ± 0.006)

(0.049 ± 0.008)

(0.063 ± 0.008)

(0.098 ± 0.008)

(0.126 ± 0.008)

(t)

Terminal

0.15 ± 0.05

0.25 ± 0.15

0.35 ± 0.15

0.50 ± 0.25

0.61 ± 0.36

(in.)

(0.006 ± 0.002)

(0.010 ± 0.006)

(0.014 ± 0.006)

(0.020 ± 0.010)

(0.024 ± 0.014)

WVDC

6.3

Cap

100

(pF)

150

220

330

470

680

1000

1500

2200

3300

4700

6800

Cap

0.010

(μF)

0.015

0.022

0.033

0.047

0.068

0.10	A	C	C		G	G	N		N
0.15					G		N	N
0.22		C		G	G		N	N	Q

0.33															G	G						N
0.47						C	C								G							N						Q	Q								X
0.68															G							N
1.0						C	C	C					G	G	G	J					N	N		P*				Q	Q						X	X	X
1.5
2.2						C						G	G	J	J					N	N	N					Q	Q							Z	X
3.3																			N	N					Q	Q
4.7												J	J						N	N	N	N*			Q	Q	Q	Q						Q	Z
10												K							N N N						Q Q Q Q								X Z Z							Z
22																			N*						Q	Q	Q					Z	Z	Z	Z
47																			*						Q							Z
100																															Z	Z*
WVDC	4	6.3	10	16	25	4	6.3	10	16	25	50	4	6.3	10	16	25	35	50	6.3	10	16	25	35	50	6.3	10	16	25	35	50	4	6.3	10	16	25	35	50	6.3	10	25	50
SIZE		0201						0402							0603						0805						1206						1210						1812

Letter	A	C	E	G	J	K	M	N	P	Q	X	Y	Z
Max.	0.33	0.56	0.71	0.90	0.94	1.02	1.27	1.40	1.52	1.78	2.29	2.54	2.79
Thickness	(0.013)	(0.022)	(0.028)	(0.035)	(0.037)	(0.040)	(0.050)	(0.055)	(0.060)	(0.070)	(0.090)	(0.100)	(0.110)
			PAPER						EMBOSSED

= Under Development

*Optional Specifications – Contact factory

NOTE: Contact factory for non-specified capacitance values

Y5V Dielectric

General Specifications

Y5V formulations are for general-purpose use in a limited temperature range. They have a wide temperature characteristic of +22% –82% capacitance change over the operating temperature range of –30°C to +85°C.

These characteristics make Y5V ideal for decoupling applications within limited temperature range.

PART NUMBER (see page 2 for complete part number explanation)

0805	3	G	104	Z	A	T	2	A

Size	Voltage		Dielectric
(L" x W")	6.3V	= 6	Y5V = G
	10V	= Z
	16V	= Y
	25V	= 3
	50V	= 5

Temperature Coefficient

	+20
	+20
	+10
	+10
Capacitance	0
	0
	-10
	-10
	-20
	-20
	-30
	-30
	-40
	-40
	-50
	-50
	-60
%	-60
%	-70
	-70
	-80
	-80

-55 -35 -15 +5 +25 +45 +65 +85 +105 +125

Temperature °C

0.1 F - 0603

Impedance vs. Frequency

10,000
10,000
	1,000
	1,000
(Ohms)\|Z\|	100
	100
	1
	10
	0.1
	0.1
	0.01
	10,000	100,000	1,000,000	10,000,000

Frequency (Hz)

Capacitance	Capacitance	Failure
Code (In pF)	Tolerance	Rate
2 Sig. Digits +	Z = +80 –20%	A = Not
Number of		Applicable
Zeros

Capacitance Change

vs. DC Bias Voltage

	+40
	+40
(%)	+20
	+20
	0
	0
c/c	-20
	-20
	-40
	-40
	-60
	-60
	-80
	-80
	-1000
	-1000	20	40	60	80	100
			% DC Bias Voltage

0.22 F - 0805

Impedance vs. Frequency

	1,000
	1,000
(Ohms)	100
	100
	10
	10
\|Z\|	1
	1

	0.1
	0.1
	0.01
	10,000	100,000	1,000,000	10,000,000

Frequency (Hz)

Terminations	Packaging		Special
T = Plated Ni	2	= 7" Reel	Code
and Sn	4	= 13" Reel	A = Std.
			Product

Insulation Resistance vs. Temperature

-Farads)	10,000
(Ohm	1,000
(Ohm
Resistance
	100







Insulation







	+20	+30	+40	+50	+60	+70	+80	+90
	0

Temperature °C

1 F - 1206

Impedance vs. Frequency

	1,000
	1,000
(Ohms)	100
	100
	10
	10
\|Z\|	1
	1

	0.1
	0.1
	0.01
	10,000	100,000	1,000,000	10,000,000

Frequency (Hz)

Y5V Dielectric

Specifications and Test Methods

Parameter/Test		Y5V Specification Limits	Measuring Conditions
Operating Temperature Range		-30ºC to +85ºC	Temperature Cycle Chamber
Capacitance		Within specified tolerance
		≤ 5.0% for ≥ 50V DC rating	Freq.: 1.0 kHz ± 10%
Dissipation Factor		≤ 7.0% for 25V DC rating	Voltage: 1.0Vrms ± .2V
Dissipation Factor		≤ 9.0% for 16V DC rating	For Cap > 10 μF, 0.5Vrms @ 120Hz
		≤ 9.0% for 16V DC rating	For Cap > 10 μF, 0.5Vrms @ 120Hz
		≤ 12.5% for ≤ 10V DC rating
Insulation Resistance		100,000MΩ or 500MΩ - μF,	Charge device with rated voltage for
Insulation Resistance		whichever is less	120 ± 5 secs @ room temp/humidity
		whichever is less	120 ± 5 secs @ room temp/humidity
Dielectric Strength			Charge device with 300% of rated voltage for
Dielectric Strength		No breakdown or visual defects	1-5 seconds, w/charge and discharge current
			limited to 50 mA (max)
	Appearance	No defects	Deflection: 2mm
Resistance to	Capacitance	≤ ±30%	Test Time: 30 seconds
	Variation	≤ ±30%	1mm/sec
	Variation		1mm/sec
Flexure	Dissipation	Meets Initial Values (As Above)
Stresses	Factor	Meets Initial Values (As Above)
Stresses	Factor
	Insulation	≥ Initial Value x 0.1	90 mm
	Resistance	≥ Initial Value x 0.1	90 mm
	Resistance

Solderability		≥ 95% of each terminal should be covered	Dip device in eutectic solder at 230 ± 5ºC
Solderability		with fresh solder	for 5.0 ± 0.5 seconds
		with fresh solder	for 5.0 ± 0.5 seconds
	Appearance	No defects, <25% leaching of either end terminal
	Capacitance	≤ ±20%
	Variation	≤ ±20%	Dip device in eutectic solder at 260ºC for 60
	Variation
	Dissipation
Resistance to	Dissipation	Meets Initial Values (As Above)	seconds. Store at room temperature for 24 ± 2
Resistance to	Factor	Meets Initial Values (As Above)	seconds. Store at room temperature for 24 ± 2
Solder Heat	Factor		hours before measuring electrical properties.
Solder Heat	Insulation	Meets Initial Values (As Above)	hours before measuring electrical properties.
	Insulation
	Resistance
	Resistance
	Dielectric	Meets Initial Values (As Above)
	Strength	Meets Initial Values (As Above)
	Strength
	Appearance	No visual defects	Step 1: -30ºC ± 2º	30 ± 3 minutes
	Capacitance	≤ ±20%	Step 2: Room Temp	≤ 3 minutes
	Variation	≤ ±20%	Step 2: Room Temp	≤ 3 minutes
	Variation
Thermal	Dissipation	Meets Initial Values (As Above)	Step 3: +85ºC ± 2º	30 ± 3 minutes
Thermal	Factor	Meets Initial Values (As Above)	Step 3: +85ºC ± 2º	30 ± 3 minutes
Shock	Factor
Shock	Insulation	Meets Initial Values (As Above)	Step 4: Room Temp	≤ 3 minutes
	Insulation
	Resistance
	Resistance
	Dielectric	Meets Initial Values (As Above)	Repeat for 5 cycles and measure after
	Strength	Meets Initial Values (As Above)	24 ±2 hours at room temperature
	Strength		24 ±2 hours at room temperature
	Appearance	No visual defects	Charge device with twice rated voltage in
	Capacitance	≤ ±30%	Charge device with twice rated voltage in
	Variation	≤ ±30%	test chamber set at 85ºC ± 2ºC
	Variation		test chamber set at 85ºC ± 2ºC
Load Life	Dissipation	≤ Initial Value x 1.5 (See Above)	for 1000 hours (+48, -0)
	Factor	≤ Initial Value x 1.5 (See Above)
	Factor		Remove from test chamber and stabilize
	Insulation	≥ Initial Value x 0.1 (See Above)	Remove from test chamber and stabilize
	Resistance	≥ Initial Value x 0.1 (See Above)	at room temperature for 24 ± 2 hours
	Resistance		at room temperature for 24 ± 2 hours
	Dielectric	Meets Initial Values (As Above)	before measuring.
	Strength	Meets Initial Values (As Above)
	Strength
	Appearance	No visual defects	Store in a test chamber set at 85ºC ± 2ºC/
	Capacitance	≤ ±30%	Store in a test chamber set at 85ºC ± 2ºC/
	Capacitance		85% ± 5% relative humidity for 1000 hours
	Variation		85% ± 5% relative humidity for 1000 hours
Load	Variation		(+48, -0) with rated voltage applied.
	Dissipation	≤ Initial Value x 1.5 (See above)	(+48, -0) with rated voltage applied.
	Dissipation
Humidity	Factor		Remove from chamber and stabilize at
Humidity	Factor
	Insulation
	Insulation	≥ Initial Value x 0.1 (See Above)	room temperature and humidity for
	Resistance	≥ Initial Value x 0.1 (See Above)	room temperature and humidity for
	Resistance		24 ± 2 hours before measuring.
	Dielectric	Meets Initial Values (As Above)	24 ± 2 hours before measuring.
	Dielectric
	Strength
	Strength

Y5V Dielectric

Capacitance Range

PREFERRED SIZES ARE SHADED

SIZE

0201

0402

0603

0805

1206

1210

Soldering

Reflow Only

Reflow/Wave

Reflow Only

Packaging

All Paper

Paper/Embossed

(L)

Length

0.60 ± 0.03

1.00 ± 0.10

1.60 ± 0.15

2.01 ± 0.20

3.20 ± 0.20

(in.)

(0.024 ± 0.001)

(0.040 ± 0.004)

(0.063 ± 0.006)

(0.079 ± 0.008)

(0.126 ± 0.008)

(W) Width

0.30 ± 0.03

0.50 ± 0.10

.81 ± 0.15

1.25 ± 0.20

1.60 ± 0.20

2.50 ± 0.20

(in.)

(0.011 ± 0.001)

(0.020 ± 0.004)

(0.032 ± 0.006)

(0.049 ± 0.008)

(0.063 ± 0.008)

(0.098 ± 0.008)

(t)

Terminal

0.15 ± 0.05

0.25 ± 0.15

0.35 ± 0.15

0.50 ± 0.25

.50 ± 0.25

(in.)

(0.006 ± 0.002)

(0.010 ± 0.006)

(0.014 ± 0.006)

(0.020 ± 0.010)

WVDC

6.3

Cap

820

(pF)

1000

2200

4700

Cap

0.010

(μF)

0.022

0.047

0.10

0.22

0.47

1.0

2.2

4.7

10.0

22.0

47.0

WVDC

6.3

SIZE

0201

0402

0603

0805

1206

1210

Letter

Max.

0.33

0.56

0.71

0.90

0.94

1.02

1.27

1.40

1.52

1.78

2.29

2.54

2.79

Thickness

(0.013)

(0.022)

(0.028)

(0.035)

(0.037)

(0.040)

(0.050)

(0.055)

(0.060)

(0.070)

(0.090)

(0.100)

(0.110)

PAPER

EMBOSSED

MLCC Tin/Lead Termination “B”

General Specifications

AVX Corporation will support those customers for commercial and military Multilayer Ceramic Capacitors with a termination consisting of 5% minimum lead. This termination is indicated by the use of a “B” in the 12th position of the AVX Catalog Part Number. This fulfills AVX’s commitment to providing a full range of products to our customers. AVX has provided in the following pages a full range of values that we are currently offering in this special “B” termination. Please contact the factory if you require additional information on our MLCC Tin/Lead Termination “B” products.

PART NUMBER (see page 2 for complete part number explanation)

LD05

101

Size	Voltage		Dielectric
LD02 - 0402	6.3V	= 6	C0G (NP0) = A
LD03 - 0603	10V	= Z	X7R = C
LD04 - 0504*	16V	= Y	X5R = D
LD05 - 0805	25V	= 3	X8R = F
LD06 - 1206	35V	= D
LD10 - 1210	50V	= 5
LD12 - 1812	100V	= 1
LD13 - 1825	200V	= 2
LD14 - 2225	500V = 7

*LD04 has the same CV ranges as LD03.

Capacitance

Code (In pF)

2 Sig. Digits +

Number of

Zeros

Capacitance

Tolerance

B = ±.10 pF (<10pF) C = ±.25 pF (<10pF) D = ±.50 pF (<10pF) F = ±1% (≥ 10 pF)

G = ±2% (≥ 10 pF) J = ±5%

K = ±10%

M = ±20%

NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values.

Failure	Terminations		Packaging	Special
Rate	B = 5% min lead	2	= 7" Reel	Code
A = Not	X = FLEXITERM®	4	= 13" Reel	A = Std.
Applicable	with 5% min	7	= Bulk Cass.	Product
	with 5% min	9	= Bulk
	lead**	9	= Bulk
	lead**

**X7R only	Contact
**X7R only	Factory
	For
	Multiples

See FLEXITERM® section for CV options

NP0	Refer to page 4 for Electrical Graphs
X7R	Refer to page 16 for Electrical Graphs
X7S	Refer to page 20 for Electrical Graphs
X5R	Refer to page 23 for Electrical Graphs
Y5V	Refer to page 26 for Electrical Graphs

<<< < Предыдущая 1 23 / 103 4 5 6 7 8 9 10 > Следующая >>>

Соседние файлы в папке Резистори, конденсатори, індуктивності

#
12.02.201666.58 Кб8cx5r.pdf
#
12.02.20162.37 Mб8F3102_T520.pdf
#
12.02.2016412.99 Кб8F3109_Kemet.pdf
#
12.02.2016124.27 Кб8PANASONIC Chip Resistor. weblc_qsg_res_0905.pdf
#
12.02.2016241.98 Кб8Pu-RC0805_51_PbFree_L_2.pdf
#
12.02.20161.75 Mб8smccp.pdf
#
12.02.20163.83 Mб9Yageo PRODUCT SELECTION GUIDE. PSG_2008_rev1.pdf
#
12.02.2016359.94 Кб9Yageo. GENERAL PURPOSE CHIP RESISTORSPYu-R_INT-thick_7.pdf
#
12.02.2016225.22 Кб11Yageo. RC0805_51. GENERAL PURPOSE CHIP RESISTORS.pdf