Chapter 7 Drawing Curves and Points 131

Placing Points

Points are generally used for reference. It is sometimes helpful to mark a point that you will use later as a guide to place an object or to help you return an object to its original position. When it’s no longer needed, you may erase the point. This is a typical construction method. In some cases, the From object snap or object snap tracking can be used instead of a point.

Changing the point style

Different disciplines have different conventions for drawing point objects. As a result, AutoCAD and AutoCAD LT provide 20 types of point styles that you can use in your drawing. Before you draw a point, you should set the point style. You can save this setting in your template.

Choose Format Point Style to open the Point Style dialog box, shown in Figure 7-9.

To set the point style, click the box showing the style that you want. Then set the point size, which has the following options:

Set Size Relative to Screen: Use this option if you want the point to always appear the same size, no matter how much you zoom in and out — for example, when you’re using the point as a reference. The size is set as a percentage of the screen. This option is the default, with the size set to 5 percent of the screen.

Set Size in Absolute Units: Use this option if you want the point to have a real size, just like any other object. The size is set in units. Use this option when you want the point to stay the same size relative to other objects in your drawing.

Click OK to close the dialog box.

Figure 7-9: Choosing a point style.

Note When you change the point style, previously drawn points automatically and immediately change to the new style.

132 Part II Drawing in Two Dimensions

Creating points

After you determine the point style, you’re ready to create points. Choose Point from the Draw toolbar.

You see the following on the command line:

Current point modes: PDMODE=0 PDSIZE=0.0000

Specify a point:

Specify the point that you want, either by picking a point on the screen or by typing coordinates. (You can specify a Z coordinate to create a point in 3D space.) You can use object snaps to specify the point. When you choose the POINT command from the Draw toolbar, the command automatically repeats the prompt so that you can continue to specify points. To end the command, press Esc. When you choose Draw Point, you can choose Single Point or Multiple Point from the submenu. The command line version draws single points.

If BLIPMODE is on and you’re using the first point style — a small dot — you cannot see the point until you use the REDRAW command to remove the blips.

STEPS: Drawing Donuts and Points

1.Open ab07-d.dwg from the CD-ROM.

2.Save the file as ab07-04.dwg in your AutoCAD Bible folder. The drawing contains a rectangle and connecting wires for an electrical switch. Make sure that OSNAP is on. Set running object snaps for endpoint, center, node, and quadrant. This exercise assumes that you have Dynamic Input on, with the default setting of relative coordinates.

3.Choose Format Point Style. The Point Style dialog box opens. Choose the third point type, which is the plus sign. The Set Size Relative to Screen option button should be check marked. The Point Size should be 5.0000%. Choose OK.

4. Choose Point from the Draw toolbar. Follow the prompts:

Specify a point: Use the From object snap. (Shift+right-click to open the Object Snap shortcut menu.)

Base point: Use the Endpoint object snap to pick the top-left corner

of the rectangle.

<Offset>: @.08,-.09

Specify a point: Press Esc to complete the command.

Chapter 7 Drawing Curves and Points 133

5.Choose Draw Donut. Follow these prompts:

Specify inside diameter of donut <0.5000>: .04 Specify outside diameter of donut <1.0000>: .06

Specify center of donut or <exit>: Use the Node object snap to pick

the point that you drew.

Specify center of donut or <exit>: @.19,0 Specify center of donut or <exit>:

6.Start the POINT command again. Follow the prompts:

Specify a point: Right-click and choose Snap Overrides Mid Between 2

Points from the shortcut menu.

First point of mid: Use the Center object snap to pick the center of the right-hand donut. (You may have to press Tab until you get the center object snap, and not a quadrant object snap.)

Second point of mid: Press and hold Shift to temporarily turn on ORTHO. Right-click and choose Snap Overrides Perpendicular and pick the lower horizontal line of the rectangle. Release the Shift key.

Specify a point: Press Esc.

7.Start the LINE command. Follow the prompts:

Specify first point: Use the Quadrant object snap to pick the right (0 degrees) quadrant of the left donut. If you don’t see the Quadrant SnapTip, press Tab until it appears.

Specify next point or [Undo]: Use the Node object snap to pick the point that you just drew. End the LINE command.

8.Save your drawing. It should look like Figure 7-10.

Figure 7-10: The completed electrical switch. The points show as plus signs.

Summary

In this chapter, you learned how to draw curved objects and points in AutoCAD and AutoCAD LT. You discovered:

All the ways to draw circles

How to define and draw an arc

How to define an ellipse and an elliptical arc

How to draw a donut

How to set the point style and draw points

In the next chapter, you read how to display your drawing for the greatest ease and comfort.