IVAN / UPRAV
.DOCУправляющая программа обработки передней панели на обрабатывающем центре ИР320.
% P001 { Упр. программа обработки передней панели} LF
N001 G80 T0101 {Фрезеровать обнижение} LF
N002 G97 S1500 F0.05 M06 M03 LF
N003 G00 X-30.25 Y25.0 Z3.0 M08 LF
N004 G01 Z-2.0 F0.14 LF
N005 X30.25 LF
N006 G00 Z3.0 LF
N007 T0202 {Центровка отверстий} LF
N008 G97 S1500 F0.1 M06 LF
N009 G00 X30.25 Y57 LF
N010 G99 G82 R3.0 Z-1.0 L17 LF
N011 Y87 LF
N012 Y117 LF
N013 X-30.25 LF
N014 Y87 LF
N015 Y57 LF
N016 X37.5 Y143.5 LF
N017 X-37.5 LF
N018 X43.0 Y175.0 LF
N019 X-43.0 LF
N020 Y10.0 LF
N021 X43.0 LF
N022 X43.0 Y130.0 LF
N023 X-43.0 LF
N024 Z-3.5 LF
N025 X30.25 Y25.0 LF
N026 X0.0 LF
N027 X-30.25 LF
N028 G80 T0303 M06 {Сверлить 6 отверстий } LF
N029 G97 S1500 F0.3 LF
N030 G00 X30.25 Y57.0 LF
N031 G99 G83 R3.0 Z-4.5 L6 LF
N032 Y87 LF
N033 Y117 LF
N034 X-30.25 LF
N035 Y87 LF
N036 Y57 LF
N037 G80 T0404 M06 {Сверлить 6 отверстий } LF
N038 G97 S1500 F0.33 LF
N039 G00 X43.0 Y130.5 LF
N040 G99 G83 L6 LF
N041 X-43.0 LF
N042 Y 175 LF
N043 X43.0 LF
N044 Y10.0 LF
N045 X-43.0 LF
N046 G80 T0505 M06 {Сверлить 2 отверстия } LF
N047 G97 S1500 F0.5 LF
N048 G00 X-37.5 Y143.5 LF
N049 G99 G83 L2 LF
N050 X37.5 LF
N051 G80 T0606 M06 {Сверлить 3 отверстия 8.3} LF
N052 G97 S1500 F0.57 LF
N053 G00 X30.25 Y25.0 LF
N054 G99 G83 L3 LF
N055 X0.0 LF
N056 X-30.25 LF
N057 G80 T0707 M06 {Сверлить 2 отверстия 2.5} LF
N058 F0.2 LF
N059 G00 X43.0 Y57.0 LF
N060 G99 G83 L2 LF
N061 X-43.0 LF
N062 G80 T0808 M06 {Сверлить 2 технологических отверстия}LF
N063 G97 S1193 F0.7 LF
N064 G00 X0.0 Y159.0 LF
N065 G99 G83 Z-4.5 LF
N066 X16.0 Y 90.0 LF
N067 G80 T0909 M06 {Вырезать окна}LF
N068 G97 S1500 F0.2 LF
N069 G00 X0.0 Y159.0 Z3.0 LF
N070 G01 Z-4.5 LF
N071 Y162.5 LF
N072 G50 X-36.5 LF
N073 G51 Y155.5 LF
N074 G49 X36.5 LF
N075 G52 Y162.5 LF
N077 G50 X0.0 LF
N078 Y160.0 LF
N079 G40 G00 Z3.0 LF
N080 X-16.0 Y90 LF
N081 G01 Z-4.5 LF
N082 G51 M59 X-20.0 LF
N083 Y48.0 LF
N084 G49 X20.0 LF
N085 G52 Y126.0 LF
N086 G51 Y90.0LF
N087 X-18.0 LF
N088 G40 T1010 M06 LF
N089 G97 S1500 F0.04 {Фрезировать углы окон}LF
N090 G00 X-18.0 Y128 Z3.0 LF
N091 G01 G50 Y130 Z-4.5 LF
N092 G46 X-24.0 LF
N093 Y124 LF
N094 G40 X-22.0 LF
N095 G00 Y50 LF
N096 G01 G51X-24.0 LF
N097 G45 Y44 LF
N098 X-18 LF
N099 G40 Y46 LF
N100 G00 X18.0 LF
N101 G01 G49 Y44.0 LF
N102 G48 X24.0 LF
N103 Y50.0 LF
N104 G40 X22.0 LF
N105 G00 Y124 LF
N106 G01 G52 X24.0 LF
N107 G47 Y130 LF
N108 X18.0 LF
N109 G40 Y128 Z3.0 LF
N110 G00 X34.5 Y153.5 LF
N111 G01 Z-4.5 LF
N112 G49 Y151.5 LF
N113 G48 X40.5 LF
N114 Y157.5 LF
N115 G40 X38.5 LF
N116 G00 Y160.5 LF
N117 G01 G52 X40.5 LF
N118 G47 Y166.5 LF
N119 X34.5 LF
N120 G40 Y164 LF
N121 G00 X-34.5 LF
N122 G01 G50 Y166.5 LF
N123 G46 X-40.5 LF
N124 Y160.5 LF
N125 G40 X-38.5 LF
N126 G00 157.5 LF
N127 G01 G51 X-40.5 LF
N128 G45 Y151.5 LF
N129 X-34.5 LF
N130 Z-2.0 {Фрезировать обнижение}LF
N131 G49 Y150.25 LF
N132 X33.75 LF
N133 G48 X41.25 LF
N134 Y158.25 LF
N135 G52 Y159.75 LF
N136 G47 Y167.25 LF
N137 X35.25 LF
N138 G50 X-33.75 LF
N139 G46 X-41.25 LF
N140 Y159.75 LF
N141 G51 Y158.25 LF
N142 G45 Y150.25 LF
N143 X-33.75 LF
N144 G40 G80 T1111 M06 {Снять фаски}LF
N145 G97 S1500 F0.75 LF
N146 G00 X30.25 Y57.0 LF
N147 G99 G82 R3.0 Z-2.9 L10 LF
N148 Y87.0 LF
N149 Y117 LF
N150 X-30.25 LF
N151 Y87 LF
N152 Y57 LF
N153 Z-3.5 X-43.0 Y10.0 LF
N154 X43.0 LF
N155 Y157 LF
N156 X-43.0 LF
N157 G80 M05 M09 M02 LF