Хорошев / ИЛП_материал_маг_02.15 / DEF STAN 00-60 / Issue 4 / Part 0 - Annex C - Data dictionary and related technical inf

C.6.10 Table BJ, Failure Mode Indicator Mission Phase Code Characteristics Narrative. This Table may be used to identify compensating design provisions and compensating operator actions. Table keys consist of EIAC (EIACODXA), LCN (LSACONXB), ALC (ALTLCNXB), LCN Type (LCNTYPXB), Failure Mode Indicator (FAMOINBF), Mission Phase Code (MISSPCBL), Failure Mode Indicator Mission Phase Characteristics Narrative Code (FMMPCNBJ), and Failure Mode Indicator Mission Phase Code Characteristics Narrative Text Sequencing Code (TEXSEQBJ). For a given row of information, the following cross-element edits apply to Table BJ:

(a)If the Failure Mode Indicator Mission Phase Characteristics Narrative Code (FMMPCNBJ) is ‘A’, then this Table describes compensating design provisions which circumvent or mitigate the effect of the failure (Compensating Design Provisions, DED 049).

(b)If the Failure Mode Indicator Mission Phase Characteristics Narrative Code (FMMPCNBJ) is ‘B’, then this Table describes compensating operator action provisions which circumvent or mitigate the effect of the failure (Compensating Operator Action Provisions, DED 050).

C.6.11 Table BK, Reliability Availability, and Maintainability Criticality. This Table sums up the failure mode criticality numbers related to the failure modes of the CI within specific safety hazard severity classification (SHSC) and mission phases. Table keys consist of EIAC (EIACODXA), LCN (LSACONXB), ALC (ALTLCNXB), LCN Type (LCNTYPXB),

C-41

DEF STAN 00-60 (PART 0)/4

ANNEX C

Mission Phase Code (MISSPCBL), and RAM SHSC (FMSHSCBK). For a given row of information, the following cross-element edits apply to Table BK:

(a)Item Criticality Number shall be calculated based on the summation of the Failure Mode Criticality Numbers (Table BI).

(b)A change in any of the Failure Mode Criticality Numbers (Table BI) shall result in an update of the Item Criticality Number (Table BK).

(c)SHSC (FMSHSCBI) shall be established in Table BI prior to establishing a RAM SHSC (FMSHSCBK) in this Table.

C.6.12 Table BL, Mission Phase Operation Mode. This Table identifies the mission phase/operational modes that the new system/EI is expected to experience during normal operation. Table keys consist of EIAC (EIACODXA) and Mission Phase Code (MISSPCBL).

C-42

DEF STAN 00-60 (PART 0)/4

ANNEX C

C.7 Task Inventory, Task Analysis, Personnel and Support Requirements

The following data Tables identified by a ‘C’ in the first position of the Table code are required for documentation of task analysis, personnel and support requirement data. Information will be presented in sufficient detail to define task times, skills, tools, support equipment, facilities, and supply support requirements. The task classification utilized to analyze and document tasks is defined in DED 372 of this Annex. Figure 9 depicts the entity diagram for these Tables.

C-43

DEF STAN 00-60 (PART 0)/4

ANNEX C

C.7.1 Table CA, Task Requirement. This Table contains task level information such as mean elapsed time, task frequency, task criticality, task identification (ID) and task code. It also contains information about personnel and training aspects of the task. In addition, this Table provides the capability to reference an entire task. Table keys consist of EIAC (EIACODXA), LCN (LSACONXB), LCN Type (LCNTYPXB), ALC (ALTLCNXB) and Task Code (TASKCDCA). For a given row of information, the following cross-element edits apply to Table CA:

(a)For referencing purposes only, Referenced LCN (REFLCNCA), Referenced LCN Type (REFTYPCA), Referenced ALC (REFALCCA), Referenced EIAC (REFEIACA), and Referenced Task Code (REFTSKCA) are mandatory keys. This referencing capability shall only be used when the data of this Table and the subordinate Tables (Tables CB through CM, except CJ) are the same for referenced and referencing tasks. All non-key attributes in Table CA and all subordinate Tables (Tables CB through CM, except CJ) are migrated from the Referenced Task and its subordinate Tables. Key attributes entered in Table CA will migrate to all subordinate Tables. Additional keys which are needed in subordinate Tables will be migrated from the Referenced Task and its subordinate Tables. In other words, only key entries and referenced entries are required in this Table and no further entries are required in subordinate Tables.

(b)Unscheduled task codes, task interval codes of ‘F’, ‘G’ or ‘J’ (2nd position of the task code), shall have an MB entered which corresponds to the MB for the AOR. For this reason, the AOR LCN (AORLCNCA), AOR ALC (AORALCCA), AOR LCN Type (AORTYPCA), and the AOR MB (AORMSBCA) shall match with a set of key values already established in Table AG.

(c)Every Task Code (TASKCDCA) shall have a Task ID (TASKIDCA).

(d)Secondary Means of Detection (SMDTECCA) is not allowed without Primary Means of Detection (PMDTECCA).

(e)Up to three Performance Standards (PRSTDACA, PRSTDBCA, and PRSTDCCA), and Task Conditions (TCONDACA, TCONDBCA, and TCONDCCA) can be entered for a given record.

(f)Every Task Code (TASKCDCA) shall have a corresponding Task Frequency (TSKFRQCA).

(g)If Requirements For (FTRNRQCA, TRNRQCCA or TSEREQCA) is ‘Y’, the associated Data Tables shall be addressed.

(h)Up to four Training Location Rationale (TRNLOCCA) codes may be entered for each unique combination of EIAC, LCN, ALC, LCN Type, and Task Code (codes shall be entered in a continuous string).

C-45

DEF STAN 00-60 (PART 0)/4

ANNEX C

(i)Up to four Training Rationale (TRNRATCA) codes may be entered for each unique combination of EIAC, LCN, ALC, LCN Type and Task Code (codes shall be entered in a continuous string).

(j)Measured Mean Man-Hours (MSDMMHCA) is calculated by summing the Mean ManMinutes (SUBMMMCD) per Subtask Person ID for the given task and dividing by 60.

(k)Measured Mean Elapsed Time (MSDMETCA) is calculated by summing the Mean Minute Elapsed Times (SBMMETCB) for all subtasks of a task and dividing by 60.

(l)Task Frequency (corrective) shall be calculated based on Failure Mode Ratio (Table BF), Failure Rate (Table BD), Mean Time Between Maintenance Induced (Table BD), Mean Time Between Maintenance No Defect (Table BD), AOR Conversion Factor (Table BA), and AOR (Table AG). Task Frequency (preventive) shall be calculated based on AOR (Table AG), AOR Conversion Factor (Table BA), Maintenance Interval (Table BH) or Task Interval Code, from subfield (b) of Task Code, DED 427 (Table CA). A change in any of these variables shall result in an update of Task Frequency (Table CA).

(m)Removal Route Condition Code (REMRCCCA) and Removal Route Number (REMRONCA) shall either both be blank or both have entries and only entered when Task Code (TASKCDCA) first subfield is set to ‘R’ or ‘H’.

C-46

C.7.2 Table CB, Subtask Requirement. This Table contains data related to the subtask level such as work area code and mean minute elapsed time. All task narrative will be written at the subtask level, then rolled into the task level. It is possible to reference subtask descriptions within this Table. Table keys consist of EIAC (EIACODXA), LCN (LSACONXB), LCN Type (LCNTYPXB), ALC (ALTLCNXB), Task Code (TASKCDCA), and Subtask Number (SUBNUMCB). For a given row of information, the following cross-element edits apply to Table CB:

(a)For referencing purposes, Referenced Subtask Number (RFDSUBCB), Referenced Subtask Task Code (RFDTCDCB), Referenced Subtask LCN (RFDLCNCB), Referenced Subtask ALC (RFDALCCB), Referenced Subtask LCN Type (RFDALCCB), and Referenced Subtask EIAC (RFDEIACB) shall be included as nonidentifying keys. This referencing capability shall only be used when the data of this Table and the subordinate tables (Sequential Subtask Description, Table CC and Subtask Personnel Requirements, Table CD) are the same for referenced and referencing subtasks. All non-key attributes in Table CB and its subordinate tables (CC and CD) are migrated from the referenced subtask and its subordinate tables.

(b)Subtask Numbers (SUBNUMCB) shall begin with 001 and run through to 999 for each unique set of keys (eg, EIAC, LCN, ALC, LCN Type, and Task Code). Gaps are allowed when assigning subtask numbers.

(c)Subtask Work Area Code (Access) (SUBWAACB) shall only be entered if there is an entry in Subtask Work Area Code (Zone) (SUBWAZCB).

NOTE: If there is a requirement to roll up data modules to a main task and therefore identify the support resource requirements for a Data Module, as defined in Part 10 of this Defence Standard, then the number of subtasks per task shall be limited to 1 and Subtask Identification (SUBTIDCB), Referenced Subtask EIAC (RFDEIACB), Referenced Subtask LCN (RFDLCNCB), Referenced Subtask ALC (RFDALCCB), Referenced Subtask LCN Type (RFDTYPCB), Referenced Subtask Task Code (RFDTCDCB) and Referenced Subtask Number (RFDSUBCB) shall all be blank.

C-47

DEF STAN 00-60 (PART 0)/4

ANNEX C

C.7.3 Table CC, Sequential Subtask Description. This Table contains the sequential task narrative entered at the subtask level. The narrative will be entered in order to document all subtasks required to perform the task under analysis. Subtasks should be detailed and sequenced to eliminate possibilities of technically incorrect procedures. Elements are subordinate to subtasks. All requirements (eg, power, compressed air, and environmental considerations) shall be specified. Qualifying notes shall be included when performance to particular standards, survivability requirements, inspection criteria, special procedures, tolerances, measurement ranges, cautions and safety precautions are required. Notes and warnings for set up of tasks (eg, identifying support items which need to be on hand and ready, but are not needed until later in the task) should be documented in the first subtask. Similarly, notes and warnings for close-down of a task should be documented in the last subtask. In cases of multi-personnel tasks, the communication and coordination requirements between personnel shall be documented (ie, communication and coordination between individuals in one work area with individuals in another area). Table keys consist of EIAC (EIACODXA), LCN (LSACONXB), ALC (ALTLCNXB), LCN Type (LCNTYPXB), Task Code (TASKCDCA), Subtask Number (SUBNUMCB), and Text Sequencing Code (TEXSEQCC). For a given row of information, the following cross-element edits apply to Table CC:

(a)The Task Element Indicator ‘E’ (ELEMNTCC) is documented against the first line of a given element narrative and is blank for all subsequent lines of that element narrative.

(b)Task Element narratives shall begin on unique lines (unique Text Sequence Codes) eg, one task element cannot end on line 12 and the next task element also begin on line 12.

C-48

C.7.4 Table CD, Subtask Personnel Requirement. This Table contains information pertaining to personnel and support requirements for each entered subtask. Table keys consist of EIAC (EIACODXA), LCN (LSACONXB), ALC (ALTLCNXB), LCN Type (LCNTYPXB), Task Code (TASKCDCA), Subtask Number (SUBNUMCB), and Subtask Person Identifier (SUBPIDCD). For a given row of information, the following cross-element edits apply to Table CD:

(a)SSC (SKSPCDGA) and New or Modified SSC (MDCSSCGB) are migrated into this Table as non-identifying attributes, which means that they are not required to uniquely identify an instance of the entity.

(b)Unique Subtask Person IDs (SUBPIDCD) may be assigned to each person required to perform a subtask and used consistently throughout the entire System/EI. If this method of Subtask Person Identification is not used, then from one task to another, the same Subtask Person ID code may be repeated for different personnel.

(c)Trade Code Manpower (TCMANPCD) shall be calculated by summing the number of rows of data for identical entries of EIAC (EIACODXA), LCN (LSACONXB), ALC (ALTLCNXB), LCN Type (LCNTYPXB), Task Code (TASKCDCA), Subtask Number (SUBNUMCB) and the specific Trade. Trade is identified in SSC (SKSPCDGA) or New or Modified SSC (MDCSSCGB), as applicable for any Subtask Number (SUBNUMCB).

(d)Trade Code Manpower (TCMANPCD) cannot be calculated unless SSC (SKSPCDGA) or New or Modified SSC (MDCSSCGB), as applicable for any Subtask Number (SUBNUMCB), is entered for all rows of data for a given Task Code (TASKCDCA).

(e)Trade Code Manpower (TCMANPCD) cannot be established for a Task Code (TASKCDCA) function other than Remove and Fit, or Replace (‘R’,’G’ or ‘H’).

C-49

DEF STAN 00-60 (PART 0)/4

ANNEX C

C.7.5 Table CE, Task Remark. This Table contains remarks, relating to the task under analysis, which are incorporated in the LSA-004 and LSA-033 Reports. Table keys are EIAC (EIACODXA) and Task Remark Reference Code (TSKRRCCE).

NOTE: Every Task Remark Reference Code and Task Remark combination is unique across all rows of information for a given EIAC. In other words, for the same EIAC, a given Task Remark Reference Code can only correspond to one Task Remark statement throughout the file structure.

C.7.6 Table CF, Task Remark Reference. This Table serves as a link table between the Task Requirement Table (CA) and the Task Remark Table (CE). Table keys consist of EIAC (EIACODXA), LCN (LSACONXB), ALC (ALTLCNXB), LCN Type (LCNTYPXB), and Task Code (TASKCDCA), which are migrated from Table CA and the Task Remark Reference Code (TSKRRCCE), which migrates from Table CE.

C.7.7 Table CG, Task Support Equipment. This Table contains information which relates data needed for the task under analysis to the Support Equipment (SE) Tables. This Table serves as the link between Task Analysis and SE areas for data which is to be incorporated into the LSA-070 series of reports. Table keys consist of EIAC (EIACODXA), LCN (LSACONXB), ALC (ALTLCNXB), LCN Type (LCNTYPXB), Task Code (TASKCDCA), Task Support CAGE Code (TSCAGECG) and Task Support Reference Number (TSREFNCG). For a given row of information, the following cross-element edits apply to Table CG:

(a)SE Quantity Per Task (SQTYTKCG) and SE Quantity Per Task Unit of Measure (SQTKUMCG) shall either both be blank, or both have entries.

(b)If the Training Equipment Requirement Code (TRNRQCCA) in Table CA is ‘Y’ for the subject LCN, ALC, and Task Code, at least one item of support equipment identified by the Task Support Reference Number (TSREFNCG) shall have an ICC (SEICCDEA) of ‘S’, ‘T’,

C-50