- •Preface
- •Section One. General
- •0 Introduction
- •1 Scope
- •2 Related Documents
- •3 Definitions
- •4 Abbreviations
- •Section Two. Electronic Documentation Process
- •5 Introduction
- •6 In-Process Review
- •7 Quality Audit
- •Section Three. Application of S1000D
- •8 Introduction
- •9 Detailed Application
- •Section Four. Electronic Documentation Data Base, Data Transfer & Data Control.
- •10 Introduction
- •11 Data Base Structure
- •12 DM Interchange
- •13 Output Deliverable Control
- •Section Five. Non-Textual Information
- •14 Introduction
- •15 Detailed Requirements
- •16 Attaching Parts
- •Section Six. Parts Information
- •17 Introduction
- •18 Preparation of Parts Information (General)
- •19 Provision of Parts Information
- •Section Seven. Operator Information
- •20 Introduction
- •21 Scope of Information
- •22 Information Requirements
- •23 Checklists
- •24 Identification of DM
- •Section Eight. Maintenance Information
- •25 Introduction
- •26 General
- •27 Preventive Maintenance
- •28 Maintenance Resource
- •Section Nine. Publications Output
- •29 Introduction
- •30 Publication Production Mechanism
- •Table 1 Revised Tag Set Definitions
- •Table 2 Spares Lists DM Information Requirements
- •Table 3 Material Item Category Code (MICC)
- •Table 4 Material Item Sub-Category Code (MISCC)
- •Table 5 Major Zone Identification Numbers
- •Table 6 Sub Zone Identification Numbers
- •Table 7 Zone Identification Numbers
- •Table 8 Major Zone Identification Number.
- •Table 9 Sub Zone Identification Number
- •Table 10 Zone Identification Numbers
- •Table 11 Equipment Zone Identification Numbers
- •Table 12 Equipment Sub Zone Identification Numbers
- •Table 13 LRU Zone Identification Numbers
- •Figure 1 Data Module Code
- •Figure 2 DMC for S1000D application
- •Figure 3 Major Zones
- •Figure 4 Major Zones
- •Figure 5 Sub Zones
- •Figure 6 Zones
- •Figure 7 Access Codes
- •Figure 8 Major Zones
- •Figure 9 Sub Zones
- •Figure 10 Zones
- •Figure 11 Equipment Zones
- •Figure 12 Equipment Sub Zones
- •Figure 13 LRU Zones
- •Figure 14 Data Module Codes for Military Systems and Associated Equipments
DEF STAN 00-60 (PART 10)/3
Section Five. Non-Textual Information
14 Introduction
14.1This Section of this Defence Standard details the requirements for the creation, storage and exchange of static, dynamic and interactive graphics and audio information. Specific differences to S1000D are also included.
14.2Within this Section of this Defence Standard, all references to graphics shall include illustrations, photographs, images, animation and video.
15 Detailed Requirements
15.1S1000D Chapter 2.6 Illustrations
15.2S1000D Chapter 2.6.1 General. To include the following:
15.2.1Where possible graphics shall perform more than one function, eg installation and removal etc. Where this is cost-effective, use shall be made of computer aided design models and derived graphics.
15.2.2Graphics shall present information clearly and directly without ambiguity and portray only the data necessary for user task.
15.3 S1000D Chapter 2.6.2 Mode of Presentation
15.3.1Colour. The requirement for the use of colour in graphics shall be specified by the Customer. Where the use of colour is specified, the ability to display and output in mono shall be ensured. eg hatching.
15.3.2Graphics. Graphics shall be prepared making maximum use of the defined display area without exceeding the stated boundary, in order to enhance clarity.
15.3.3Figures and Hands. Human figures shall only be used where it is essential to show manual handling. All human detail shall be in proportion to the mechanical detail.
16 Attaching Parts
16.1When identical fasteners attach a component or assembly, an instance shall be located using fence lines drawn solid, single line weight and indexed.
16.2Families of attaching parts shall be drawn at the foot of the graphic area in preference to being included within the detail.
16.3Plate nuts shall not be illustrated but their location shall be indicated by the bore-hole and associated holes on their respective item/assembly.
20
DEF STAN 00-60 (PART 10)/3
16.4S1000D Chapter 2.6.3 General Symbols and Use of Standard Symbols. Graphical symbols for engineering drawings etc shall be in accordance with the relevant ISO or British Standard. Where a non-standard symbol is required a legend shall be included.
16.5S1000D Chapter 2.6.4 Type of Illustrations. The following features are included in addition to those in S1000D:
16.5.1 Schematic Diagrams
16.5.1.1The direction of flow shall be clearly identified where appropriate. Schematic diagrams shall show the relationship of the components comprising the system.
16.5.1.2The most logical presentation of information shall be used to indicate flow from left to right and/or top to bottom. Unnecessary cross-over and changes of direction shall be avoided.
16.5.1.3Where inter-lines are shown these shall be produced such that the individual lines are discernible in the appropriate end-user display. To avoid groups of multiple parallel lines, single cable form routing techniques may be used.
16.5.2 Other Non-Textual Information
16.5.2.1 Animation, Audio and Full Motion Video shall be used when their use aids understanding and their application is agreed by the Customer. The motion of animated information shall be clearly discernible by the user and clearly differentiated from the background and other static information of the related display.
16.6S1000D Chapter 2.6.5 Format/Line Weights/Typeface/Type Sizes. Format, line weights, typeface and type sizes shall be as per S1000D except that the preparation of graphics for the display on A3 sized paper or large screen shall be avoided. The use of smaller and linked images shall be utilised where appropriate.
16.7S1000D Chapter 2.6.6 Figure Title and Number. S1000D is not applicable. Every graphic shall be given a title and shall be contained within its own unique DM with associated DMC.
16.8S1000D Chapter 2.6.7 Illustration Control Number and Source of Origin. S1000D is not applicable. Every graphic shall be contained within its own DM with the associated management and status information defined.
16.9S1000D Chapter 2.6.8 Location Drawings. As per S1000D.
16.10S1000D Chapter 2.6.9 Reference Illustrations. As per S1000D.
16.11S1000D Chapter 2.6.10 Callout and Reference Lines. As per S1000D.
21
DEF STAN 00-60 (PART 10)/3
16.12S1000D Chapter 2.6.11 Centre Lines Projection Lines. Centre lines and projection lines shall be as per S1000D except that centre lines shall be applied to clarify the relationships of exploded parts and assemblies and shall be portrayed in ‘dot, dash’ single line weight presentation.
16.13S1000D Chapter 2.6.12 Illustration of View, Details and Sections. As per S1000D
16.14S1000D Chapter 2.6.13 Identification of Electrical and Electronic Components. Identification of electrical and electronic components shall be as per S1000D and additionally to include block and functional diagram items that are necessarily indexed in the detail of the illustration shall be identified against a key in the graphic area. Full page keys shall be treated separately.
16.15S1000D Chapter 2.6.14 Mirrored Item. As per S1000D.
16.16S1000D Chapter 2.6.15 Illustration of Different Configurations. As per S1000D.
16.17S1000D Chapter 2.6.16 Item Tabulation. As per S1000D.
22