12 Related Documentation and Resources

Not Recommended For New Designs (NRND)

Espressif Systems

25

ESP32-WROVER Datasheet v2.7

Date

Version

Release notes

Major updates:

• Removed contents about hall sensor according to PCN20221202

Other updates:

2023-02-09

v2.7

• Added information about the setup and hold times for the strapping pins in

Section 2.3

• Added source files of PCB land patterns and 3D models of the modules (if

available) in Section 9: Recommended PCB Land Pattern

• Added Chapter 11

Added a link to RF certificates in Table 2

2022.04

v2.6

Updated Table 6

Added a note below Figure 5

Replaced Espressif Product Ordering Information with ESP Product Selector

2021.08

v2.5

Updated the description of TWAI in Table 2

Labeled this document as (Not Recommended For New Designs)

Updated Figure 5: Physical Dimensions of ESP32-WROVER and Figure 6: Recom-

2021.02

V2.4

mended PCB Land Pattern of ESP32-WROVER.

Modified the note below Figure Reflow Profile.

Updated the trade mark from TWAI™ to TWAI®.

Added TWAITM in Table 2;

2020.11

V2.3

Added a note to Figure Reflow Profile;

Added documentation feedback link;

Updated the C value in RC circuit from 0.1 µF to 1 µF.

• Added Moisture sensitivity level (MSL) 3 in Table 2 ESP32-WROVER Specifica-

tions;

• Added notes about ”Operating frequency range” and ”TX power” under Table

2019.09

V2.2

9 Wi-Fi Radio Characteristics;

• Updated Section 7 Peripheral Schematics and added a note about RC delay

circuit under it;

• Updated Figure 9 Recommended PCB Land Pattern.

2019.01

V2.1

Added a note on the use of GPIO12 under Table 3, as well as in Section 4;

Changed the RF power control range in Table 11 from –12 ~ +12 to –12 ~ +9 dBm.

Updated the recommended operating temperature from –40 °C ~ 65 °C to –40 °C

2018.11

V2.0

~ 85 °C.

Updated Chapter 6: Schematics, where C18 is changed from a 1 µF capacitor to a

4.7 µF capacitor.

2018.10

V1.9

Added ”Cumulative IO output current” entry to Table 6: Absolute Maximum Ratings;

Added more parameters to Table 8: DC Characteristics.

Not Recommended For New Designs (NRND)

Espressif Systems

26

ESP32-WROVER Datasheet v2.7

Date

Version

Release notes

• Added certifications and reliability test items the module has passed in Table 2:

ESP32-WROVER Specifications, and removed software-specific information;

• Updated Section 3.4: RTC and Low-Power Management;

• Changed the module’s dimensions from (18±0.15) mm x (31.4 ±0.2) mm x

(3.5±0.15) mm to (18.00±0.10) mm x (31.40±0.10) mm x (3.30±0.10) mm;

2018.08

V1.8

• Updated Figure 8: Physical Dimensions;

• Updated Chapter 6: Schematics;

• Changed the recommended operating temperature from –40°C ~ 85°C to –

40°C ~ 65°C and added a note to custom order of ESP32-WROVER with high

temperature range;

• Corrected a typo in Electrical Characteristics section;

• Updated Table 9: Wi-Fi Radio.

• Updated the capacity of PSRAM from 32 Mbit to 64 Mbit;

• Deleted Temperature Sensor in Table 2: ESP32-WROVER Specifications;

• Updated Chapter 3: Functional Description;

• Updated Chapter 6: Schematics;

• Added Chapter 9: Recommended PCB Land Pattern;

2018.06

V1.7

Changes to electrical characteristics:

• Updated Table 6: Absolute Maximum Ratings;

• Added Table 7: Recommended Operating Conditions;

• Added Table 8: DC Characteristics;

• Updated the values of ”Gain control step”, ”Adjacent channel transmit power”

in Table 11: Transmitter Characteristics - BLE.

2018.03

V1.6

Corrected typos in Table 3 Pin Definitions.

2018.03

V1.5

Updated Table 2 in Chapter 1.

2018.03

V1.4

Updated Chapter 6 Schematics;

Updated Chapter 8 Dimensions.

Updated section 3.4 RTC and Low-Power Management;

2018.01

V1.3

Deleted information on LNA pre-amplifier;

Updated section 3.4 RTC and Low-Power Management;

Updated the ESP32-WROVER schematics in Chapter 6;

Added a note in Chapter 7;

Added the U.FL dimensions (Figure 10).

Updated the description of the chip’s system reset in Section 2.3 Strapping Pins;

Deleted ”Association sleep pattern” in Table ”Power Consumption by Power Modes”

2017.10

V1.2

and added notes to Active-sleep and Modem-sleep;

Added a note to Output Impedance in Table 9;

Updated the notes to Figure 4 Peripheral Schematics.

Updated Section 2.1 Pin Layout;

2017.09

V1.1

Updated the ESP32-WROVER Schematics and dded a note in Chapter 7;

Added Chapter 8 Dimensions.

2017.08

V1.0

First release.

Not Recommended For New Designs (NRND)

Espressif Systems

27

ESP32-WROVER Datasheet v2.7

Disclaimer and Copyright Notice

Information in this document, including URL references, is subject to change without notice.

ALL THIRD PARTY’S INFORMATION IN THIS DOCUMENT IS PROVIDED AS IS WITH NO

WARRANTIES TO ITS AUTHENTICITY AND ACCURACY.

NO WARRANTY IS PROVIDED TO THIS DOCUMENT FOR ITS MERCHANTABILITY, NON-

INFRINGEMENT, FITNESS FOR ANY PARTICULAR PURPOSE, NOR DOES ANY WARRANTY

OTHERWISE ARISING OUT OF ANY PROPOSAL, SPECIFICATION OR SAMPLE.

All liability, including liability for infringement of any proprietary rights, relating to use of information

in this document is disclaimed. No licenses express or implied, by estoppel or otherwise, to any

intellectual property rights are granted herein.

The Wi-Fi Alliance Member logo is a trademark of the Wi-Fi Alliance. The Bluetooth logo is a

registered trademark of Bluetooth SIG.

All trade names, trademarks and registered trademarks mentioned in this document are property

www.espressif.com

of their respective owners, and are hereby acknowledged.

Copyright © 2023 Espressif Systems (Shanghai) Co., Ltd. All rights reserved.