ПОМТ (Мочалин ФИБС БТС 8 семестр) / Сервисная инструкция

Service Handbook

Appendix

8

A"#$0$

Checklist

8.1

Name of tester:

Visa:

Device serial number:

Software Version:

Customer:

Date:

Reference/Testpoints

OK

False

Remark

5.2.1 Internal Sight Control page 34

1.

Plugs are properly in the socket and secured

2.

All protective cable (green/yellow) are properly laid out and securely con-

nected to one the earth point (potential equalisation).

3.

All Cables connection between the individual printer boards are not

crushed anywhere or lying on sharp parts (i.e. protective shields). If ca-

bles have to be lead passed a sharp part, it is important that they are pro-

tected by a special shield

4.

Isolation foils and shields are built in correctly and are certainly not left out

or forgotten (see explosion drawings)

5.

Check that no loose parts are inside the device by tipping the device, or

turning it upside down

5.2.2 External Sight Control page 34

1.

Voltage selector is set correctly

2.

Fuses according table (see page 45)

3.

Safety labels are on the device and are readable

4.

Mechanical condition of the device allows a further safe operation (cracks

in the shell, mains cable, etc.).

5.

there is no soiling which could hamper the safety of the device.

5.2.3 Mains indicator LED test page 35

1.

The mains indicator lamp (6) is always lit when the unit is connected to the

a

mains supply.

Rev.:

2.

The relevant symbol is displayed on the LCD (7).

2.540037

3.

The mains indicator lamp (6) switches off and the symbol battery is dis-

played on the LCD (7).

no.:

5.2.4 Power Supply test page 35

Art.-

1.

Unloaded current (device switched off) 35...70 mA

2.

Operating current (device switched on) 45...85 mA

5.2.5 Keyboard test page 35

1.

Check the keyboard for mechanical damage. If any can be seen, the key-

board is to be replaced.

2.

Check all function keys for their proper operation. An acoustic confirma-

tion appears whenever a function key is pressed.

5.2.6 LCD Screen test page 35

1.

The contrast has to be variable from very dark to very light.

2.

Visually check the screen for spots, or black fields. If such appear, the

LCD has to be replaced. The LCD has to be the same shade everywhere.

If one side is darker, the background lighting should be checked.

Page 59

8

Appendix

8.1

Checklist

A"#$0$

Reference/Testpoints

OK

False

Remark

3.

The mains indicator lamp (6) switches off and the symbol battery is dis-

played on the LCD (7).

5.2.7 Paper Feed page 36

1.

The paper has to stop exactly at the perforation. If this is not the case, con-

trol the paper mark comparison.

5.2.8 Printer quality test page 36

1.

Check the blackness for regularity and good readability on the complete

print width.

2.

Check on the 25 mm/s printout if the space between 2 R peaks according

to the paper grids. The space should be 25 mm and may not show a dif-

ference of more than ± 0.5 mm.

5.2.9 Printing Speed page 36

1.

Check on the 25 mm/s printout if the space between 2 R peaks according

to the paper grids. The space should be 25 mm and may not show a dif-

HR is set to 60

ference of more than ± 0.5 mm.

5.2.10 Parallelism test page 37

1.

All calibration impulses should be lined up vertically and exactly below

one another.

2.

The maximum deviation may not be more than ± 0.5 square. If the values

are outside this tolerance, the mechanical adjustment of the print head

has to be corrected.

5.2.11 ECG amplifier page 37

1.

Check the amplitude height of the calibration impulse according to the pa-

per grid. It should be 20 mm ±0.5 square.

5.2.12 ECG lead and patient cable test page 38

1.

all leads (1) are blinking

2.

Uel for all leads is -350 to -550 mV

3.

all leads stops blinking

4.

Uel for all leads is -15 ...+15 mV

5.

Udif = 3985 ...4015 mV

6.

TPH = 18 ...30 °C

a

Rev.:

7.

Check amplitude and polarity according printouts

5.2.13 External printer test page 41

2.540037

1.

all leads (1) are blinking

2.

Uel for all leads is -350 to -550 mV

no.:

3.

all leads stops blinking

Art.-

4.

Uel for all leads is -15 ...+15 mV

5.

Udif = 3985 ...4015 mV

6.

TPH = 18 ...30 °C

7.

Check amplitude and polarity according printouts

5.2.14 Communication (RS-232) Test page 41

1.

The screen shows hex characters when the serial port is ok.

5.3 Safety Tests page 42

1.

The safety test is carried out in accordance with the EN 60601-1, Clause

18 and 19. This test may only be carried out with a tester that fulfils the

Add protocol to the checklist

above mentioned norms and has been calibrated in accordance with ISO

norms.

Page 60

Service Handbook

Appendix

8

A"#$0$

Checklist

8.1

8

Appendix

8.1

Checklist

A"#$0$