MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document by MBRP20060CT/D
Designer's Data Sheet
SWITCHMODE
Schottky Power Rectifier
POWERTAP II Package
. . . employing the Schottky Barrier principle in a large area metal±to±silicon power diode. State of the art geometry features epitaxial construction with oxide passivation and metal overlay contact. Ideally suited for low voltage, high frequency switching power supplies, free wheeling diode and polarity protection diodes.
•Guardring for Stress Protection
•Matched dual die construction ± May be Paralleled for High Current Output
•High dv/dt Capability
•Very Low Forward Voltage Drop
Mechanical Characteristics:
•Case: Epoxy, Molded with Metal Heatsink Base
•Weight: 80 grams (approximately)
•Finish: All External Surfaces Corrosion Resistant
•Base Plate Torques: See procedure given in the Package Outline Section
•Top Terminal Torque: 70 in±lb max.
•Shipped 25 units per foam
•Marking: MBRP20060CT
MBRP20060CT
SCHOTTKY BARRIER
RECTIFIER
200 AMPERES
60 VOLTS
3
2
CASE 357C-03
POWERTAP II
MAXIMUM RATINGS
Rating |
|
Symbol |
Value |
Unit |
||
|
|
|
|
|
|
|
Peak Repetitive Reverse Voltage |
|
VRRM |
|
60 |
Volts |
|
Working Peak Reverse Voltage |
|
VRWM |
|
|
|
|
DC Blocking Voltage |
|
VR |
|
|
|
|
Average Rectified Forward Current |
Per Leg |
IO |
100 |
Amps |
||
(At Rated VR, TC = 120°C) |
Per Package |
|
200 |
|
||
Peak Repetitive Forward Current |
Per Leg |
IFRM |
200 |
Amps |
||
(At Rated VR, Square Wave, 20 kHz, TC = 125°C) |
|
|
|
|
|
|
Non-Repetitive Peak Surge Current |
Per Package |
IFSM |
1500 |
Amps |
||
(Surge applied at rated load conditions, halfwave, single phase, 60 Hz) |
|
|
|
|
|
|
|
|
|
|
|
|
|
Storage/Operating Case Temperature |
|
Tstg, TC |
± 55 to +150 |
°C |
||
Operating Junction Temperature |
|
TJ |
± 55 to +150 |
°C |
||
Voltage Rate of Change (Rated VR, TJ = 25°C) |
|
dv/dt |
1,000 |
V/μs |
||
THERMAL CHARACTERISTICS |
|
|
|
|
|
|
|
|
|
|
|
|
|
Thermal Resistance Ð Junction±to±Case |
Per Leg |
Rtjc |
0.44 |
°C/W |
||
ELECTRICAL CHARACTERISTICS |
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum Instantaneous Forward Voltage (1), see Figure 2 |
Per Leg |
VF |
TJ = 25°C |
|
TJ = 100°C |
Volts |
(IF = 100 Amps) |
|
|
0.80 |
|
0.72 |
|
(IF = 200 Amps) |
|
|
0.92 |
|
0.82 |
|
Maximum Instantaneous Reverse Current, see Figure 4 |
Per Leg |
IR |
TJ = 25°C |
|
TJ = 100°C |
mA |
(VR = 60 V) |
|
|
0.5 |
|
100 |
|
(VR = 30 V) |
|
|
0.2 |
|
50 |
|
(1) Pulse Test: Pulse Width ≤ 250 μs, Duty Cycle ≤ 2%.
POWERTAP and SWITCHMODE are trademarks of Motorola, Inc.
Motorola, Inc. 1995
MBRP20060CT |
|
|
|
|
|
|||
CURRENT (AMPS) |
1000 |
|
|
|
|
|
|
|
100 |
|
|
|
|
|
|
|
|
FORWARD |
|
|
|
|
|
|
|
|
|
TJ = 150°C |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
, INSTANTANEOUS |
10 |
|
|
25°C |
|
|
|
|
|
|
|
|
|
|
|
||
|
100°C |
|
|
|
|
|
|
|
1.0 |
|
|
|
|
|
|
|
|
F |
|
|
|
|
|
|
|
|
I |
0.2 |
0.3 |
0.4 |
0.5 |
0.6 |
0.7 |
0.8 |
0.9 |
|
||||||||
|
|
VF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) |
|
|||||
Figure 1. Typical Forward Voltage
|
1.0 |
|
|
|
|
|
|
(AMPS) |
0.1 |
|
|
TJ = 150°C |
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
CURRENT |
0.01 |
|
|
|
|
|
|
|
|
|
100°C |
|
|
|
|
, REVERSE |
|
|
|
|
|
|
|
0.001 |
|
|
|
|
|
|
|
0.0001 |
|
|
|
|
|
|
|
R |
|
|
|
|
|
|
|
I |
|
|
|
|
|
|
|
0.00001 |
|
|
25°C |
|
|
|
|
0.000001 |
10 |
20 |
30 |
40 |
50 |
60 |
|
|
0 |
||||||
VR, REVERSE VOLTAGE (VOLTS)
Figure 3. Typical Reverse Current
CURRENT(AMPS) |
1000 |
|
|
|
|
|
|
|
|
100 |
|
|
|
|
|
|
|
|
|
FORWARD |
|
|
|
|
|
|
|
|
|
|
TJ = 150°C |
|
|
|
|
|
|
|
|
, INSTANTANEOUS |
10 |
|
|
|
|
|
|
|
|
|
|
|
25°C |
|
|
|
|
||
|
|
|
|
|
|
|
|
||
|
100°C |
|
|
|
|
|
|
|
|
1.0 |
|
|
|
|
|
|
|
|
|
F |
|
|
0.5 |
0.6 |
0.7 |
0.8 |
|
|
|
I |
0.2 |
0.3 |
0.4 |
0.9 |
1.0 |
||||
|
|||||||||
|
VF, MAXIMUM INSTANTANEOUS FORWARD VOLTAGE (VOLTS) |
|
|||||||
Figure 2. Maximum Forward Voltage
(AMPS) |
1.0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CURRENT |
0.1 |
|
|
|
|
|
|
|
|
|
100°C |
|
|
|
|
0.01 |
|
|
|
|
|
|
|
REVERSE |
|
|
|
|
|
|
|
0.001 |
|
|
|
|
|
|
|
, MAXIMUM |
0.0001 |
|
|
° |
|
|
|
|
|
|
25 C |
|
|
|
|
|
|
|
|
|
|
|
|
R |
|
|
|
|
|
|
|
I |
|
|
|
|
|
|
|
|
0.00001 |
10 |
20 |
30 |
40 |
50 |
60 |
|
0 |
VR, REVERSE VOLTAGE (VOLTS)
Figure 4. Maximum Reverse Current
(AMPS) |
160 |
|
|
dc |
|
|
FREQ = 20 kHz |
||
140 |
|
|
|
|
|||||
|
|
|
|
|
|
|
|
||
CURRENT |
120 |
|
|
SQUARE |
|
|
|
|
|
|
|
WAVE |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
||
100 |
|
|
Ipk/Io = p |
|
|
|
|
||
FORWARD |
|
|
|
|
|
|
|
||
80 |
|
|
Ipk/Io = 5 |
|
|
|
|
||
|
|
|
|
|
|
|
|||
60 |
|
|
|
|
|
|
|
|
|
, AVERAGE |
|
|
|
|
|
|
|
|
|
40 |
|
|
Ipk/Io = 10 |
|
|
|
|
||
|
|
Ipk/Io = 20 |
|
|
|
|
|||
|
|
|
|
|
|
|
|||
20 |
|
|
|
|
|
|
|
|
|
O |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
I |
|
|
|
|
|
|
|
|
|
|
0 |
20 |
40 |
60 |
80 |
100 |
120 |
140 |
160 |
|
0 |
||||||||
|
|
|
|
TC, CASE TEMPERATURE (°C) |
|
|
|||
Figure 5. Current Derating
(PER LEG)
(WATTS) |
120 |
|
|
|
|
|
dc |
|
|
|
|
|
|
|
|
||
100 |
|
|
|
|
|
|
|
|
DISSIPATION |
|
|
|
SQUARE |
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
WAVE |
|
|
|
|
80 |
|
|
Ipk/Io = p |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
POWER |
60 |
|
Ipk/Io = 5 |
|
|
|
|
|
Ipk/Io = 10 |
|
|
|
|
|
|||
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
AVERAGE |
40 |
Ipk/Io = 20 |
|
|
|
|
|
|
20 |
|
|
|
|
|
|
|
|
, |
|
|
|
|
|
|
TJ = 150°C |
|
FO |
|
|
|
|
|
|
|
|
P |
0 |
|
|
|
|
|
|
|
|
25 |
50 |
75 |
100 |
125 |
150 |
175 |
|
|
0 |
|||||||
|
|
|
IO, AVERAGE FORWARD CURRENT (AMPS) |
|
||||
Figure 6. Forward Power Dissipation
(PER LEG)
2 |
Motorola Schottky Power Rectifier Data |
C, CAPACITANCE (pF)
MBRP20060CT
10,000
TJ = 25°C
1,000
100 |
10 |
100 |
1.0 |
VR, REVERSE VOLTAGE (VOLTS)
Figure 7. Capacitance
(NORMALIZED) |
1.0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
RESISTANCE |
0.1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
THERMAL |
0.01 |
|
|
|
Rtjc(t) = Rtjc*r(t) |
|
|
|
|
|
|
|
|
|
|
|
|||
TRANSIENT |
0.001 |
|
|
|
|
|
|
|
|
, |
0.00001 |
0.0001 |
0.001 |
0.01 |
0.1 |
1.0 |
10 |
100 |
|
(T) |
|||||||||
|
|
|
|
|
|
|
|
||
R |
|
|
|
|
T, TIME (s) |
|
|
|
|
|
|
|
|
|
|
|
|
Figure 8. Thermal Response
|
VCC |
|
+ 150 V, |
|
|
12 Vdc |
|
10 mAdc |
|
12 V |
100 |
|
|
2 kW |
2N2222 |
D.U.T. |
|
||
|
|
|
||
2 ms |
CURRENT |
|
2N6277 |
|
1 kHz |
|
+ |
||
|
AMPLITUDE |
100 W |
|
4 mF |
|
ADJUST |
CARBON |
1 CARBON |
|
|
0 ±10 AMPS |
|
|
|
|
|
|
|
|
|
|
|
1N5817 |
|
Figure 9. Test Circuit for Repetitive
Reverse Current
Motorola Schottky Power Rectifier Data |
3 |
MBRP20060CT
MAXIMUM MECHANICAL RATINGS
Terminal Penetration: |
0.235 max |
|
|
Terminal Torque: |
70 in-lb max |
|
|
Mounting Torque Ð |
|
Outside Holes: |
70 in-lb max |
|
|
Mounting Torque Ð |
|
Center Hole: |
8±10 in-lb max |
|
|
Seating Plane |
1 mil per in. |
Flatness |
(between mounting holes) |
|
|
POWERTAP MECHANICAL DATA
APPLIES OVER OPERATING TEMPERATURE
2″ |
Vertical Pull |
2 in. Lever Pull |
250 lbs. max |
50 lbs. max |
Note: While the POWERTAP is capable of sustaining these vertical and levered tensions, the intimate contact
Note: between POWERTAP and heat sink may be lost. This could lead to thermal runaway. The use of very
Note: flexible leads is recommended for the anode connections. Use of thermal grease is highly recommended.
MOUNTING PROCEDURE
The POWERTAP package requires special mounting considerations because of the long longitudinal axis of the copper heat sink. It is important to follow the proper tightening sequence to avoid warping the heat sink, which can reduce thermal contact between the POWERTAP and heat sink.
STEP 1:
Locate the POWERTAP on the heat sink and start mounting bolts into the threads by hand (2 or 3 turns).
2 ± 3 TURNS |
|
|
|
2 ± 3 TURNS |
|
|
|
2 ± 3 TURNS |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
POWER |
TAP |
HEAT |
SINK |
STEP 2:
Finger tighten the center bolt. The bolt may catch on the threads of the heat sink so it is important to make sure the face of the bolt or washer is in contact with the surface of the POWERTAP.
STEP 3:
Tighten each of the end bolts between 5 to 10 in-lb.
STEP 4:
Tighten the center bolt between 8 to 10 in-lb.
STEP 5:
Finally, tighten the end bolts to 70 in-lb.
2 ± 3 TURNS |
|
|
|
FINGER-TIGHT |
|
|
|
2 ± 3 TURNS |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
POWER |
TAP |
HEAT |
SINK |
5 ± 10 IN-LB |
|
|
|
FINGER-TIGHT |
|
|
|
5 ± 10 IN-LB |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
POWER |
TAP |
HEAT |
SINK |
5 ± 10 IN-LB |
|
|
|
8 ± 10 IN-LB |
|
|
|
5 ± 10 IN-LB |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
POWER |
TAP |
HEAT |
SINK |
70 IN-LB |
|
|
|
8 ± 10 IN-LB |
|
|
|
70 IN-LB |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
POWER |
TAP |
HEAT |
SINK |
4 |
Motorola Schottky Power Rectifier Data |
MBRP20060CT
PACKAGE DIMENSIONS
|
-A- |
W |
|
|
|
|
|
|
NOTES: |
|
|
|
|
|
|
|
|
|
|
|
|
1. DIMENSIONING AND TOLERANCING PER ANSI |
|||||||
|
R |
|
0.25 (0.010) M |
T |
A |
M |
B |
M |
|
Y14.5M, 1982. |
|
|
|
|
|
|
2. |
CONTROLLING DIMENSION: INCH. |
|
||||||||||
|
G |
|
|
|
|
|
|
|
3. TERMINAL PENETRATION: 5.97 (0.235) MAXIMUM. |
|||||
|
N |
|
|
|
|
|
|
|
|
INCHES |
MILLIMETERS |
|||
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
||||
-B- |
|
|
|
|
|
|
|
|
|
DIM |
MIN |
MAX |
MIN |
MAX |
|
|
|
|
|
|
|
|
|
A |
3.450 |
3.635 |
87.63 |
92.33 |
|
|
|
|
|
|
|
|
|
|
|
B |
0.700 |
0.810 |
17.78 |
20.57 |
|
|
Q 2 PL |
|
|
|
|
|
|
C |
0.615 |
0.640 |
15.53 |
16.26 |
|
|
|
|
0.25 (0.010) M |
T |
A |
M |
B |
M |
|
E |
0.120 |
0.130 |
3.05 |
3.30 |
H |
F |
|
|
F |
0.435 |
0.445 |
11.05 |
11.30 |
||||||
|
|
|
|
|
|
|
|
|
|
G |
1.370 |
1.380 |
34.80 |
35.05 |
|
|
|
|
|
|
|
|
|
|
H |
0.007 |
0.030 |
0.18 |
0.76 |
|
|
|
|
|
|
|
|
|
|
N |
1/4±20UNC 2B |
1/4±20UNC 2B |
||
|
|
-T- |
SEATING |
|
|
|
|
|
|
Q |
0.270 |
0.285 |
6.86 |
7.32 |
C |
|
|
|
|
|
|
|
R |
31.50 BSC |
80.01 BSC |
||||
|
PLANE |
|
|
|
|
|
|
|||||||
|
E |
|
|
|
|
|
|
U |
0.600 |
0.630 |
15.24 |
16.00 |
||
|
|
|
|
|
|
|
|
|
||||||
U |
V |
|
|
|
|
|
|
|
|
V |
0.330 |
0.375 |
8.39 |
9.52 |
|
|
|
|
|
|
|
|
|
|
W |
0.170 |
0.190 |
4.32 |
4.82 |
CASE 357C±03
ISSUE C
Motorola Schottky Power Rectifier Data |
5 |
MBRP20060CT
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. ªTypicalº parameters can and do vary in different applications. All operating parameters, including ªTypicalsº must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and 
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us: |
|
USA / EUROPE: Motorola Literature Distribution; |
JAPAN: Nippon Motorola Ltd.; Tatsumi±SPD±JLDC, Toshikatsu Otsuki, |
P.O. Box 20912; Phoenix, Arizona 85036. 1±800±441±2447 |
6F Seibu±Butsuryu±Center, 3±14±2 Tatsumi Koto±Ku, Tokyo 135, Japan. 03±3521±8315 |
MFAX: RMFAX0@email.sps.mot.com ± TOUCHTONE (602) 244±6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, |
|
INTERNET: http://Design±NET.com |
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852±26629298 |
◊ MBRP20060CT/D
*MBRP20060CT/D*