motorola / 74HC240A
.PDF
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Octal 3-State Inverting Buffer/MC54/74HC240A
Line Driver/Line Receiver
High±Performance Silicon±Gate CMOS |
|
J SUFFIX |
|
The MC54/74HC240A is identical in pinout to the LS240. The device |
20 |
CERAMIC PACKAGE |
|
CASE 732±03 |
|||
|
|||
inputs are compatible with standard CMOS outputs; with pullup resistors, |
|
1 |
|
they are compatible with LSTTL outputs. |
|
|
|
This octal noninverting buffer/line driver/line receiver is designed to be |
|
N SUFFIX |
|
used with 3±state memory address drivers, clock drivers, and other |
|
||
|
PLASTIC PACKAGE |
||
sub±oriented systems. The device has inverting outputs and two active±low |
20 |
||
CASE 738±03 |
|||
output enables. |
|
||
|
1 |
||
The HC240A is similar in function to the HC241A and HC244A. |
|
||
|
|
• Output Drive Capability: 15 LSTTL Loads |
|
DW SUFFIX |
||
20 |
SOIC PACKAGE |
|||
• |
Outputs Directly Interface to CMOS, NMOS, and TTL |
|||
1 |
CASE 751D±04 |
|||
• Operating Voltage Range: 2 to 6 V |
|
|
||
• Low Input Current: 1 μA |
|
DT SUFFIX |
||
• |
High Noise Immunity Characteristic of CMOS Devices |
20 |
TSSOP PACKAGE |
|
1 |
CASE 948E±02 |
|||
• |
In Compliance with the Requirements Defined by JEDEC Standard |
|||
|
|
|||
|
No. 7A |
ORDERING INFORMATION |
||
• Chip Complexity: 120 FETs or 30 Equivalent Gates |
||||
MC54HCXXXAJ |
Ceramic |
|||
|
|
|||
MC74HCXXXAN Plastic
|
|
|
|
|
|
MC74HCXXXADW |
|
SOIC |
|
|
|
|
|
|
|
MC74HCXXXADT |
|
TSSOP |
|
|
|
|
|
LOGIC DIAGRAM |
|
|
|
|
|
|
A1 |
2 |
|
18 |
YA1 |
PIN ASSIGNMENT |
|||
|
A2 |
4 |
|
16 |
YA2 |
ENABLE A |
1 |
20 |
VCC |
|
|
6 |
|
14 |
|
A1 |
2 |
19 |
ENABLE B |
|
A3 |
|
YA3 |
YB4 |
3 |
18 |
YA1 |
||
|
A4 |
8 |
|
12 |
YA4 |
A2 |
4 |
17 |
B4 |
|
|
YB3 |
5 |
16 |
YA2 |
||||
DATA |
|
|
|
INVERTING |
|||||
INPUTS |
11 |
9 |
OUTPUTS |
A3 |
6 |
15 |
B3 |
||
|
B1 |
|
|
|
YB1 |
|
|
|
|
|
|
13 |
7 |
|
YB2 |
7 |
14 |
YA3 |
|
|
B2 |
YB2 |
A4 |
8 |
13 |
B2 |
|||
|
B3 |
15 |
5 |
YB3 |
YB1 |
9 |
12 |
YA4 |
|
|
GND |
10 |
11 |
B1 |
|||||
|
|
|
|
|
|
||||
|
B4 |
17 |
3 |
YB4 |
|
|
|
|
|
|
|
|
|
PIN 20 = VCC |
FUNCTION TABLE |
||||
|
|
|
1 |
|
|
|
|
||
OUTPUT |
ENABLE A |
PIN 10 = GND |
|
Inputs |
Outputs |
||||
ENABLES |
ENABLE B |
19 |
|
|
Enable A, |
|
|
||
|
|
|
|
|
|
Enable B A, B |
YA, YB |
||
|
|
|
|
|
|
L |
L |
|
H |
|
|
|
|
|
|
L |
H |
|
L |
|
|
|
|
|
|
H |
X |
|
Z |
|
|
|
|
|
|
Z = high impedance |
|
||
10/95
Motorola, Inc. 1995 |
REV 6 |
MC54/74HC240A
MAXIMUM RATINGS*
Symbol |
Parameter |
Value |
Unit |
|
|
|
|
|
|
VCC |
DC Supply Voltage (Referenced to GND) |
± 0.5 to + 7.0 |
V |
|
Vin |
DC Input Voltage (Referenced to GND) |
± 1.5 to VCC + 1.5 |
V |
|
Vout |
DC Output Voltage (Referenced to GND) |
± 0.5 to VCC + 0.5 |
V |
|
Iin |
DC Input Current, per Pin |
± 20 |
mA |
|
Iout |
DC Output Current, per Pin |
± 35 |
mA |
|
ICC |
DC Supply Current, VCC and GND Pins |
± 75 |
mA |
|
PD |
Power Dissipation in Still Air, Plastic or Ceramic DIP² |
750 |
mW |
|
|
SOIC Package² |
500 |
|
|
|
TSSOP Package² |
450 |
|
|
|
|
|
|
|
Tstg |
Storage Temperature |
± 65 to + 150 |
_C |
|
TL |
Lead Temperature, 1 mm from Case for 10 Seconds |
|
_C |
|
|
(Plastic DIP, SOIC or TSSOP Package) |
260 |
|
|
|
(Ceramic DIP) |
300 |
|
|
|
|
|
|
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high±impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC. Unused inputs must always be
tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open.
*Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions.
²Derating Ð Plastic DIP: ± 10 mW/ _C from 65_ to 125_C Ceramic DIP: ± 10 mW/_C from 100_ to 125_C SOIC Package: ± 7 mW/_C from 65_ to 125_C
TSSOP Package: ± 6.1 mW/_C from 65_ to 125_C
For high frequency or heavy load considerations, see Chapter 2 of the Motorola High±Speed CMOS Data Book (DL129/D).
RECOMMENDED OPERATING CONDITIONS
Symbol |
Parameter |
|
Min |
Max |
Unit |
|
|
|
|
|
|
VCC |
DC Supply Voltage (Referenced to GND) |
|
2.0 |
6.0 |
V |
Vin, Vout |
DC Input Voltage, Output Voltage (Referenced to GND) |
0 |
VCC |
V |
|
TA |
Operating Temperature, All Package Types |
|
± 55 |
+ 125 |
_C |
tr, tf |
Input Rise and Fall Time |
VCC = 2.0 V |
0 |
1000 |
ns |
|
(Figure 1) |
VCC = 4.5 V |
0 |
500 |
|
|
|
VCC = 6.0 V |
0 |
400 |
|
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
|
|
|
|
|
Guaranteed Limit |
|
||
|
|
|
|
VCC |
|
|
|
|
|
|
|
|
± 55 to |
|
|
|
|
Symbol |
Parameter |
Test Conditions |
V |
25_C |
v 85_C |
v 125_C |
Unit |
|
|
|
|
|
|
|
|
|
|
VIH |
Minimum High±Level Input |
Vout = 0.1 V |
2.0 |
1.5 |
1.5 |
1.5 |
V |
|
|
Voltage |
|Iout| v 20 μA |
4.5 |
3.15 |
3.15 |
3.15 |
|
|
|
|
|
|
6.0 |
4.2 |
4.2 |
4.2 |
|
|
|
|
|
|
|
|
|
|
VIL |
Maximum Low±Level Input |
Vout = VCC ± 0.1 V |
2.0 |
0.5 |
0.5 |
0.5 |
V |
|
|
Voltage |
|Iout| v 20 |
μA |
4.5 |
1.35 |
1.35 |
1.35 |
|
|
|
|
|
6.0 |
1.8 |
1.8 |
1.8 |
|
|
|
|
|
|
|
|
|
|
VOH |
Minimum High±Level Output |
Vin = VIL |
μA |
2.0 |
1.9 |
1.9 |
1.9 |
V |
|
Voltage |
|Iout| v 20 |
4.5 |
4.4 |
4.4 |
4.4 |
|
|
|
|
|
|
6.0 |
5.9 |
5.9 |
5.9 |
|
|
|
|
|
|
|
|
|
|
|
|
Vin = VIL |
|Iout| v 6.0 mA |
4.5 |
3.98 |
3.84 |
3.70 |
|
|
|
|
|Iout| v 7.8 mA |
6.0 |
5.48 |
5.34 |
5.20 |
|
VOL |
Maximum Low±Level Output |
Vin = VIH |
μA |
2.0 |
0.1 |
0.1 |
0.1 |
V |
|
Voltage |
|Iout| v 20 |
4.5 |
0.1 |
0.1 |
0.1 |
|
|
|
|
|
|
6.0 |
0.1 |
0.1 |
0.1 |
|
|
|
|
|
|
|
|
|
|
|
|
Vin = VIH |
|Iout| v 6.0 mA |
4.5 |
0.26 |
0.33 |
0.40 |
|
|
|
|
|Iout| v 7.8 mA |
6.0 |
0.26 |
0.33 |
0.40 |
|
Iin |
Maximum Input Leakage Current |
Vin = VCC or GND |
6.0 |
± 0.1 |
± 1.0 |
± 1.0 |
μA |
|
MOTOROLA |
2 |
MC54/74HC240A
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
|
|
|
|
Guaranteed Limit |
|
||
|
|
|
|
|
|
|
|
|
|
|
VCC |
± 55 to |
|
|
|
Symbol |
Parameter |
Test Conditions |
V |
25_C |
v 85_C |
v 125_C |
Unit |
|
|
|
|
|
|
|
|
IOZ |
Maximum Three±State |
Output in High±Impedance State |
6.0 |
± 0.5 |
± 5.0 |
± 10 |
μA |
|
Leakage Current |
Vin = VIL or VIH |
|
|
|
|
|
|
|
Vout = VCC or GND |
|
|
|
|
|
ICC |
Maximum Quiescent Supply |
Vin = VCC or GND |
6.0 |
4 |
40 |
160 |
μA |
|
Current (per Package) |
Iout = 0 μA |
|
|
|
|
|
NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High±Speed CMOS Data Book (DL129/D).
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
|
|
|
Guaranteed Limit |
|
||
|
|
VCC |
|
|
|
|
|
|
± 55 to |
|
|
|
|
Symbol |
Parameter |
V |
25_C |
v 85_C |
v 125_C |
Unit |
|
|
|
|
|
|
|
tPLH, |
Maximum Propagation Delay, A to YA or B to YB |
2.0 |
80 |
100 |
120 |
ns |
tPHL |
(Figures 1 and 3) |
4.5 |
16 |
20 |
24 |
|
|
|
6.0 |
14 |
17 |
20 |
|
|
|
|
|
|
|
|
tPLZ, |
Maximum Propagation Delay, Output Enable to YA or YB |
2.0 |
110 |
140 |
165 |
ns |
tPHZ |
(Figures 2 and 4) |
4.5 |
22 |
28 |
33 |
|
|
|
6.0 |
19 |
24 |
28 |
|
|
|
|
|
|
|
|
tPZL, |
Maximum Propagation Delay, Output Enable to YA or YB |
2.0 |
110 |
140 |
165 |
ns |
tPZH |
(Figures 2 and 4) |
4.5 |
22 |
28 |
33 |
|
|
|
6.0 |
19 |
24 |
28 |
|
|
|
|
|
|
|
|
tTLH, |
Maximum Output Transition Time, Any Output |
2.0 |
60 |
75 |
90 |
ns |
tTHL |
(Figures 1 and 3) |
4.5 |
12 |
15 |
18 |
|
|
|
6.0 |
10 |
13 |
15 |
|
|
|
|
|
|
|
|
Cin |
Maximum Input Capacitance |
Ð |
10 |
10 |
10 |
pF |
Cout |
Maximum Three±State Output Capacitance (Output in |
Ð |
15 |
15 |
15 |
pF |
|
High±Impedance State) |
|
|
|
|
|
|
|
|
|
|
|
|
NOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the Motorola High± Speed CMOS Data Book (DL129/D).
|
|
Typical @ 25°C, VCC = 5.0 V |
|
CPD |
Power Dissipation Capacitance (Per Transceiver Channel)* |
32 |
pF |
*Used to determine the no±load dynamic power consumption: PD = CPD VCC2f + ICC VCC. For load considerations, see Chapter 2 of the Motorola High±Speed CMOS Data Book (DL129/D).
3 |
MOTOROLA |
MC54/74HC240A |
|
|
|
|
|
|
|
|
SWITCHING WAVEFORMS |
|
|
|
|
|
|
|
ENABLE |
50% |
|
VCC |
|
tr |
tf |
|
GND |
||
DATA INPUT |
90% |
|
VCC |
tPZL |
tPLZ |
|
A OR B |
|
|
|
|||
50% |
|
|
|
|
HIGH |
|
|
10% |
|
GND |
|
|
|
|
|
50% |
|
IMPEDANCE |
||
|
tPHL |
tPLH |
OUTPUT Y |
|
||
|
10% |
VOL |
||||
|
90% |
|
|
tPZH |
||
OUTPUT |
50% |
|
|
tPHZ |
VOH |
|
YA OR YB |
10% |
|
OUTPUT Y |
50% |
90% |
|
|
|
|
HIGH |
|||
|
|
|
|
|||
|
tTHL |
tTLH |
|
|
|
|
|
|
|
|
IMPEDANCE |
||
|
|
|
|
|
|
|
Figure 1. |
Figure 2. |
|
TEST POINT |
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
OUTPUT |
|
|
|
|
|
|
|||
DEVICE |
|
|
|
|
|
|
|
|
|
DEVICE |
|
|
|
|
|
|
|
|
|
||
UNDER |
|
|
|
|
|
|
|
|
CL* |
UNDER |
TEST |
|
|
|
|
|
|
|
|
TEST |
|
|
|
|
|
|
|
|
||||
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* Includes all probe and jig capacitance
Figure 3. Test Circuit
PIN DESCRIPTIONS
TEST POINT |
|
|
OUTPUT |
1 kΩ |
CONNECT TO VCC WHEN |
|
TESTING tPLZ AND tPZL. |
|
|
|
CONNECT TO GND WHEN |
TESTING tPHZ AND tPZH.
CL*
* Includes all probe and jig capacitance
Figure 4. Test Circuit
INPUTS
A1, A2, A3, A4, B1, B2, B3, B4 (Pins 2, 4, 6, 8, 11, 13, 15, 17)
Data input pins. Data on these pins appear in inverted form on the corresponding Y outputs, when the outputs are enabled.
CONTROLS
Enable A, Enable B (Pins 1, 19)
Output enables (active±low). When a low level is applied
to these pins, the outputs are enabled and the devices function as inverters. When a high level is applied, the outputs assume the high±impedance state.
OUTPUTS
YA1, YA2, YA3, YA4, YB1, YB2, YB3, YB4 (Pins 18, 16, 14, 12, 9, 7, 5, 3)
Device outputs. Depending upon the state of the output± enable pins, these outputs are either inverting outputs or high±impedance outputs.
MOTOROLA |
4 |
MC54/74HC240A
LOGIC DETAIL
TO THREE OTHER
A OR B INVERTERS
ONE OF 8
INVERTERS
DATA VCC
INPUT
A OR B
YA
OR
YB
ENABLE A
OR ENABLE B
5 |
MOTOROLA |
MC54/74HC240A
OUTLINE DIMENSIONS
|
|
J SUFFIX |
|
|
CERAMIC PACKAGE |
20 |
11 |
CASE 732±03 |
|
|
ISSUE E |
1 |
10 |
|
|
|
|
|
B |
|
|
A |
|
|
|
|
F |
|
C |
L |
|
|
|
|||
|
|
N |
J |
|
H |
|
K |
||
G |
M |
|||
D |
|
|||
|
|
|||
SEATING |
|
|
|
|
PLANE |
|
|
|
NOTES:
1.LEADS WITHIN 0.25 (0.010) DIAMETER, TRUE POSITION AT SEATING PLANE, AT MAXIMUM MATERIAL CONDITION.
2.DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL.
3.DIMENSIONS A AND B INCLUDE MENISCUS.
|
MILLIMETERS |
INCHES |
||
DIM |
MIN |
MAX |
MIN |
MAX |
A |
23.88 |
25.15 |
0.940 |
0.990 |
B |
6.60 |
7.49 |
0.260 |
0.295 |
C |
3.81 |
5.08 |
0.150 |
0.200 |
D |
0.38 |
0.56 |
0.015 |
0.022 |
F |
1.40 |
1.65 |
0.055 |
0.065 |
G |
2.54 BSC |
0.100 BSC |
||
H |
0.51 |
1.27 |
0.020 |
0.050 |
J |
0.20 |
0.30 |
0.008 |
0.012 |
K |
3.18 |
4.06 |
0.125 |
0.160 |
L |
7.62 BSC |
0.300 BSC |
||
M |
0 |
15 |
0 |
15 |
N |
0.25 |
1.02 |
0.010 |
0.040 |
|
|
|
|
|
|
|
|
|
N SUFFIX |
|
|
|
|
|
|
|
|
|
|
±A± |
|
|
|
|
PLASTIC PACKAGE |
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
CASE 738±03 |
|
|
NOTES: |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
ISSUE E |
|
|
1. DIMENSIONING AND TOLERANCING PER ANSI |
||||||
20 |
|
|
|
|
|
11 |
|
|
|
|
|
Y14.5M, 1982. |
|
|
|
|
||
|
|
|
|
|
|
|
B |
|
|
|
|
2. CONTROLLING DIMENSION: INCH. |
|
|||||
|
|
|
|
|
|
|
|
|
|
|
3. DIMENSION L TO CENTER OF LEAD WHEN |
|||||||
1 |
|
|
|
|
|
10 |
|
|
|
|
|
|
FORMED PARALLEL. |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
4. DIMENSION B DOES NOT INCLUDE MOLD |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
C |
L |
|
|
|
FLASH. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
INCHES |
|
MILLIMETERS |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
DIM |
MIN |
MAX |
|
MIN |
MAX |
|
|
|
|
|
|
|
|
|
|
|
|
|
A |
1.010 |
1.070 |
25.66 |
27.17 |
|
±T± |
|
|
|
|
|
|
|
|
|
|
|
|
B |
0.240 |
0.260 |
|
6.10 |
6.60 |
|
|
|
|
|
|
K |
|
|
|
|
|
C |
0.150 |
0.180 |
|
3.81 |
4.57 |
|
SEATING |
|
|
|
|
|
|
|
|
|
|
|
D |
0.015 |
0.022 |
|
0.39 |
0.55 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
M |
|
|
|
E |
0.050 BSC |
|
1.27 BSC |
|||
PLANE |
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
E |
|
|
|
|
N |
|
|
|
|
|
|
F |
0.050 |
0.070 |
|
1.27 |
1.77 |
|
|
|
|
|
|
|
|
|
|
|
G |
0.100 BSC |
|
2.54 BSC |
||||
G |
F |
|
|
|
|
|
|
|
|
|
|
|
J |
0.008 |
0.015 |
|
0.21 |
0.38 |
|
|
|
|
|
|
|
J 20 PL |
|
|
|
K |
0.110 |
0.140 |
|
2.80 |
3.55 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
D 20 PL |
|
|
0.25 (0.010) M |
T |
B |
M |
L |
0.300 BSC |
|
7.62 BSC |
|||
|
|
|
|
|
|
|
M |
0 |
15 |
|
0 |
15 |
||||||
|
|
|
|
|
|
0.25 (0.010) M |
T |
A M |
|
|
|
N |
0.020 |
0.040 |
|
0.51 |
1.01 |
|
|
|
|
|
|
|
|
|
|
DW SUFFIX |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PLASTIC SOIC PACKAGE |
|
|
NOTES: |
|
|
|
|
|
|
||
|
±A± |
|
|
|
|
|
|
CASE 751D±04 |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
1. DIMENSIONING AND TOLERANCING PER |
|||||||||
|
|
|
|
|
|
|
|
|
ISSUE E |
|
|
|||||||
20 |
|
|
|
11 |
|
|
|
|
|
|
ANSI Y14.5M, 1982. |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
2. CONTROLLING DIMENSION: MILLIMETER. |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
3. DIMENSIONS A AND B DO NOT INCLUDE |
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
MOLD PROTRUSION. |
|
|
|
|
||
|
|
|
|
±B± |
10X P |
|
|
|
|
|
4. MAXIMUM MOLD PROTRUSION 0.150 |
|
||||||
|
|
|
|
|
|
|
|
|
(0.006) PER SIDE. |
|
|
|
|
|||||
|
|
|
|
|
|
|
0.010 (0.25) M |
B M |
|
|
5. DIMENSION D DOES NOT INCLUDE |
|
||||||
|
|
|
|
|
|
|
|
|
DAMBAR PROTRUSION. ALLOWABLE |
|
||||||||
1 |
|
|
|
10 |
|
|
|
|
|
|
|
DAMBAR PROTRUSION SHALL BE 0.13 |
|
|||||
|
|
|
|
|
|
|
|
|
|
(0.005) TOTAL IN EXCESS OF D DIMENSION |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
AT MAXIMUM MATERIAL CONDITION. |
|
|||||
20X D |
|
|
|
|
|
|
J |
|
|
|
|
MILLIMETERS |
INCHES |
|
||||
|
0.010 (0.25) M |
T |
A |
|
B |
|
|
|
|
|
DIM |
MIN |
MAX |
MIN |
MAX |
|
||
|
S |
S |
|
|
|
|
|
A |
12.65 |
12.95 |
0.499 |
0.510 |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
B |
7.40 |
7.60 |
0.292 |
0.299 |
||
|
|
|
|
|
|
|
|
F |
|
|
|
C |
2.35 |
2.65 |
0.093 |
0.104 |
||
|
|
|
|
|
|
|
|
|
|
|
D |
0.35 |
0.49 |
0.014 |
0.019 |
|||
|
|
|
|
|
|
|
|
|
|
|
|
F |
0.50 |
0.90 |
0.020 |
0.035 |
||
|
|
|
|
|
|
|
|
|
R X 45 |
|
|
G |
1.27 BSC |
|
0.050 BSC |
|
||
|
|
|
|
|
|
|
|
|
|
|
J |
0.25 |
0.32 |
0.010 |
0.012 |
|||
|
|
|
|
|
|
|
|
|
|
|
|
K |
0.10 |
0.25 |
0.004 |
0.009 |
||
|
|
|
|
|
|
|
|
|
|
|
|
M |
0 |
7 |
|
0 |
7 |
|
|
|
|
|
|
C |
|
|
|
|
|
|
P |
10.05 |
10.55 |
0.395 |
0.415 |
||
|
|
|
|
|
|
|
|
|
|
|
R |
0.25 |
0.75 |
0.010 |
0.029 |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
±T± |
SEATING |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PLANE |
|
M |
|
|
|
|
|
|
|
|
|
|
18X G |
|
|
|
K |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MOTOROLA |
|
|
|
|
|
|
|
|
6 |
|
|
|
|
|
|
|
|
|
MC54/74HC240A
OUTLINE DIMENSIONS
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948E±02
ISSUE A
|
|
|
|
20X K REF |
|
|
0.15 (0.006) |
T |
U S |
|
0.10 (0.004) M T U S V S |
|
K |
|
|
|
|
|
|
|
|
|
|
20 |
11 |
|
K1 |
|
2X L/2 |
|
|
|||
|
|
|
|
|
||
|
|
|
|
B |
J J1 |
|
L |
|
|
|
|
|
|
|
PIN 1 |
|
±U± |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
SECTION N±N |
|
|
|
IDENT |
|
|
|
|
|
|
|
1 |
10 |
|
|
|
|
|
|
|
N |
0.25 (0.010) |
|
|
|
|
|
|
|
0.15 (0.006) |
T |
U S |
|
|
|
|
|
|
|
|
A |
|
M |
|
|
|
|
|
|
|
|
|
|
|
±V± |
|
|
|
|
|
|
|
N |
|
|
|
|
|
|
|
F |
|
|
|
|
|
|
DETAIL E |
C |
|
|
D |
G |
H |
|
||
0.100 (0.004) |
|
DETAIL E |
|
|
|
±T± SEATING |
|
|
PLANE |
|
|
NOTES:
1.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2.CONTROLLING DIMENSION: MILLIMETER.
3.DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE.
4.DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5.DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION.
6.TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY.
7.DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE ±W±.
|
|
|
MILLIMETERS |
INCHES |
||
|
|
DIM |
MIN |
MAX |
MIN |
MAX |
|
|
A |
6.40 |
6.60 |
0.252 |
0.260 |
|
|
B |
4.30 |
4.50 |
0.169 |
0.177 |
|
|
C |
±±± |
1.20 |
±±± |
0.047 |
|
|
D |
0.05 |
0.15 |
0.002 |
0.006 |
|
|
F |
0.50 |
0.75 |
0.020 |
0.030 |
|
|
G |
0.65 BSC |
0.026 BSC |
||
|
|
H |
0.27 |
0.37 |
0.011 |
0.015 |
|
|
J |
0.09 |
0.20 |
0.004 |
0.008 |
±W± |
|
J1 |
0.09 |
0.16 |
0.004 |
0.006 |
|
|
K |
0.19 |
0.30 |
0.007 |
0.012 |
|
|
K1 |
0.19 |
0.25 |
0.007 |
0.010 |
|
|
L |
6.40 BSC |
0.252 BSC |
||
|
|
M |
0 |
8 |
0 |
8 |
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. ªTypicalº parameters can and do vary in different applications. All operating parameters, including ªTypicalsº must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and 
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us: |
|
USA/EUROPE: Motorola Literature Distribution; |
JAPAN: Nippon Motorola Ltd.; Tatsumi±SPD±JLDC, Toshikatsu Otsuki, |
P.O. Box 20912; Phoenix, Arizona 85036. 1±800±441±2447 |
6F Seibu±Butsuryu±Center, 3±14±2 Tatsumi Koto±Ku, Tokyo 135, Japan. 03±3521±8315 |
MFAX: RMFAX0@email.sps.mot.com ±TOUCHTONE (602) 244±6609 |
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, |
INTERNET: http://Design±NET.com |
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852±26629298 |
◊ CODELINE MC54/74HC240A/D
*MC54/74HC240A/D*