Fieldbus Controller 750-837, /02x-000, 750-838, /02x-000 |
• 49 |
Operating system |
|
|
|
3.1.3 Operating system
3.1.3.1 Start-up
The controller starts-up after switching on the supply voltage or after a hardware reset. The PLC program in the flash memory is transferred to the RAM.
This is followed by the initialization of the system. The controller determines the I/O modules and the present configuration. The variables are set to 0 or to FALSE or to an initialization value given by the PLC program. The flags retain their status . The "I/O" LED blinks red during this phase.
Following an error free start-up, the controller changes over to the "RUN" mode. The "I/O" LED lights up green.
More Information
The evaluation of the displayed LED signals is described in Chapter 3.1.8 "LED Display"
A PLC program does not yet exist in the flash memory when delivered. The controller start-up is described without initializing the system. It then behaves as a coupler.
3.1.3.2 PLC cycle
The PLC cycle starts following an error free start-up when the operating mode switch is in the top position or by a start command from the WAGO-I/O-PRO CAA. The input and output data of the fieldbus and the I/O modules as well as the times are read. Subsequently the PLC program in the RAM is processed followed by the output data of the fieldbus and the I/O
modules in the process image. Operating system functions, amongst others, for diagnosis and communication are performed and the times are updated at the end of the PLC cycle. The cycle starts again with the reading in of the input and output data and the times.
The change of the operating mode (STOP/RUN) is made at the end of a PLC cycle.
The cycle time is the time from the start of the PLC program to the next start. If a loop is programmed within a PLC program, the PLC running time and thus the PLC cycle are extended correspondingly.
The inputs, outputs and times are not updated during the processing of the PLC program. This update occurs in a defined manner only at the end of the PLC program. For this reason it is not possible to wait for an event from the process or the elapse of a time within a loop.
WAGO-I/O-SYSTEM 750
CANopen
50• Fieldbus Controller 750-837, /02x-000, 750-838, /02x-000 Operating system
|
Switching on the |
|
|
|
supply voltage |
|
|
|
|
|
|
|
|
|
|
|
Is a PLC |
No |
|
|
program in the Flash |
||
|
|
||
“I/O” LED |
memory ? |
|
|
|
|
|
|
is blinking |
|
Yes |
|
orange
PLC program transfer from the flash memory to RAM
|
Determination of the I/O modules |
||
|
and the configuration |
|
|
|
|
|
|
|
|
|
|
|
Initialization |
|
|
|
of the system |
|
|
“I/O” LED |
|
|
|
is blinking |
|
|
|
red |
|
|
No |
|
Test o.k.? |
||
|
|
||
Yes
STOP
Operating mode
RUN
PLC cycle
Reading inputs, outputs and times
PLC program in the RAM is processed
“I/O” LED
is shining green
Writing outputs
Operating system functions, updating times
STOP
Operating mode
RUN
Fig. 3-10: Controller operating system
Determination of the I/O modules and the configuration
Variables are set to 0 or FALSE or to their initial value,
flags remain in the same status.
Stop |
No |
Test o.k.? |
|
Yes
operating mode switch is in the top position or start command in WAGO-IO-PRO 32:
Online/Start or Online/Stop
Fieldbus data,
data of I/O modules
Fieldbus start behaviour as a coupler
Fieldbus data,
data of I/O modules
operating mode switch is in the top position or 
start command in WAGO-IO-PRO 32:
Online/Start or Online/Stop
g012x41x
WAGO-I/O-SYSTEM 750
CANopen