3.7. Запуск монитора

_{∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙}

The RUN MONITOR has several functions and which are as follows: EPI RUN, MACH. DISPLAY and DIM DISPLAY.

3.7.1. EPI – Запуск

Users can select the edited program for EPI automatic run.
1.Program selection and machining start specification Program Selection …
		[EPI RUN]- Enter the status for EPI RUN operation. [MACH. DISPLAY]-Enter the status for EPI RUN operation.
Program № select …
	Enter program N0.0(1-99) = Например: "1".
Call the edited program by entering the desired program № on the command line. The first two blocks of the current program are displayed in the block area. Program N s equential number select …
		To specify the starting initial block, enter the block №, such as "N4".

30701- 1

3.7. Запуск монитора

_{∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙}

Users can specify the N sequential number as the initial block. Input the N sequential number on the command line. : (1) The current new input program number will replace the specified program. (2) To modify the current program in progress, the program should be reset firstly and then enter new program №. (3) During machining, if press [MANUAL] (экранная клавиша), the running program is aborted. During machining, if нажать [PARAMETER] (экранная клавиша), then the running program is feedholded.

30701-2

3.7. Запуск монитора

_{∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙}

2.RUN, Feedhold and Restart Program run ....
	[EPI RUN]- [MACH. DISPLAY]-Enter the status of EPI RUN operation.
Input the desired and edited program №, such as: 1.
	[Enter]. [START]- Start to execute specified program.
: Preparation before machining-•... (1) The zero point should be returned. (2) Set the zero point coordinate of workpiece. (3) The machining only can be started after dielectric fluid level reaches its level when "level ON" is turned ON. During non- submerging machining the "level ON" key should be turned OFF.

30701- 3