- •Introduction
- •1. Introduction Введение
- •1.1 Contents of the instruction manual Содержание инструкционного руководства
- •1.2 Important warnings
- •1.3 Preservation of the manual
- •1.4 Definitions
- •Improper use that
- •2. Technical characteristics
- •2.1 Expected use of the machine
- •2.2 Technical data
- •General characteristics
- •2.3 Description of the machine
- •Characteristics
- •2.6 Remaining risks
- •Warnings
- •3. Installation of the machine
- •3.1 Preparation of the work area, care of the customer
- •3.2 Electric connections
- •3.3 Pneumatic connections
- •4. Functioning and adjustments
- •Introduction
- •4.1 Functioning
- •4.2 Adjustment of horizontal electropneumatic units
- •4.3 Adjustment of the vertical drilling units
- •4.4 Adjustment of the horizontal/lateral drilling units
- •4.5 Adjustment of the piece holding benches
- •4.6 Adjustment of the loader ca2
- •4.7 Adjustment of the magazine
- •4.8 Control board [ Fig. 4.8 ]
- •5. Handling and transport
- •6. Maintenance
- •6.1 Particulars
- •6.2 Description
4.2 Adjustment of horizontal electropneumatic units
* Adjustment of the depth of the holes into the piece.
1) Loosen the locking screw ( # 1, fig. 4.2 ).
2) By means of the knob adjust the position of the reference ( # 2 ): the distance between this and the limit-switch [+]( # 3 ) determi-nes the useful working run.
3) At the end of the adjustment, tighten the locking screw.
* Adjustment in height of the electropneumatic units.
1) Loosen the locking gib ( # 5, fig. 4.2 ).
2) By means of the nut ( # 6 ) adjust the position of the unit, making reference to the mechanic counter.
3) Then, tighten again the locking gib.
* Transversal adjustment of the units.
1) Loosen the handle ( # 7, fig. 4.2 ).
2) Adjust by hand the position of the unit ( # 8 ), with reference to the millimetre line [ Optional: digital read-out ( # 9 ) ].
3) At the end, secure back again the handle.
page 18
4.3 Adjustment of the vertical drilling units
* Adjustment of the drilling depth.
1) Loosen the locking screw ( # 1, fig. 4.3 ).
2) Adjust the position of the reference ( # 2 ), by means of the knob on the mechanic counter ( # 3 ).
3) At the end of the adjustment, tighten the locking screw.
* Transversal adjustment of the units.
1) Loosen the handle ( # 5, fig. 4.3 ).
2) Adjust by hand the position of the unit ( # 6 ), making reference to the digital read-out ( # 9 ).
3) At the end of the adjustment, secure again the handle.
* Frontal adjustment of the units.
1) Loosen the locking gib ( # 7, fig. 4.3 ).
2) Using the screw ( # 8 ) adjust the position of the unit, making reference to the millimetre line.
3) At the end of the adjustment, tighten again the locking gib.
4.4 Adjustment of the horizontal/lateral drilling units
* Adjustment of the depth of the holes into the piece.
1) Loosen the locking screw ( # 1, fig. 4.4 ).
2) Adjust the position of the reference ( # 2 ), by means of the knob on the mechanic counter ( # 3 ).
3) At the end of the adjustment, tighten the locking screw.
* Frontal adjustment of the units.
1) Loosen the locking gib ( # 5, fig. 4.4 ).
2) Using the screw ( # 6 ) adjust the position of the group, making reference to the mechanic revs-counter.
3) At the end, tighten back again the locking gib.
* Height of the holes compared to benches’ reference.
1) Loosen the locking gib ( # 7, fig. 4.4 ).
2) Using the handle ( # 8 ) adjust the position of the group, making reference to the mechanic counter. Then tighten back the gib.
page 19
* Adjustment of the distance between the lateral groups.
1) Loosen the handle ( # 9, fig. 4.4 ).
2) Adjust by hand the position of the unit ( # 10 ), making reference to the digital read-out. At the end, secure again the handle.
PAY ATTENTION.
The adjustment of the right unit is carried out at the same time and by means of the adjustment of the right wing of the magazine. The unit at the left usually remains fix.