acer extensa 5635
.pdf
Removing the USB Board
1.See “Removing the Upper Cover” on page 60.
2.Open the locking latch on the FFC and disconnect it from the Mainboard.
3.Open the locking latch on the FFC and disconnect it from the USB Board.
4.Remove the adhesive tape securing the USB FFC to the Lower Cover and remove the cable.
Chapter 3 |
71 |
Downloaded from www.Manualslib.com manuals search engine
5.Remove the two screws securing the USB Board to the Lower Cover.
Step |
|
Size |
Quantity |
Screw Type |
|
|
|
|
|
USB Board |
M2.5*5 |
|
2 |
|
|
|
|
|
|
6.Remove the USB Board from the Lower Cover as shown.
|
|
|
|
|
|
|
|
72 |
|
Chapter 3 |
|
Downloaded from www.Manualslib.com manuals search engine
Removing the Mainboard
1.See “Removing the Hinge Supports” on page 75.
2.Turn the computer over. Disconnect the power cable from the Mainboard as shown.
3.Remove the single screw securing the Mainboard to the Lower Cover.
Step |
|
Size |
Quantity |
Screw Type |
|
|
|
|
|
Mainboard |
M2.5*5 |
|
1 |
|
|
|
|
|
|
Chapter 3 |
73 |
Downloaded from www.Manualslib.com manuals search engine
4.Rotate the Mainboard upward and remove it from the chassis, right side first. Place the Mainboard on a clean, dust-free surface.
74 |
Chapter 3 |
Downloaded from www.Manualslib.com manuals search engine
Removing the Hinge Supports
1.See “Removing the Mainboard” on page 73.
2.Remove the four screws (one on the left and three on the right) securing the Hinge Supports to the Lower Cover.
Step |
|
Size |
Quantity |
Screw Type |
|
|
|
|
|
Hinge Supports |
M2.5*4 |
|
4 |
|
|
|
|
|
|
3.Lift the Hinge Supports clear of the Lower Cover.
Chapter 3 |
75 |
Downloaded from www.Manualslib.com manuals search engine
Removing the Thermal Module
1.See “Removing the Mainboard” on page 73.
2.Disconnect the fan cable from the Mainboard.
3.Loosen the six captive screws (in reverse numerical order from screw 6 to screw 1) securing the Thermal Module in place.
4
5
6
3 
2
1
4.Lift the Thermal Module clear of the Mainboard.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
76 |
|
|
|
Chapter 3 |
|
Downloaded from www.Manualslib.com manuals search engine
Removing the CPU
1.See “Removing the Thermal Module” on page 76.
2.Turn the securing screw 180° to release the CPU from the socket.
3.Remove the CPU from the socket as shown.
IMPORTANT: The pins on the underside of the CPU are very delicate. If they are damaged, the CPU may malfunction. Place the CPU on a clean, dry surface when it is not installed.
|
|
|
|
|
|
|
|
Chapter 3 |
77 |
||
Downloaded from www.Manualslib.com manuals search engine
LCD Module Disassembly Process
IMPORTANT:Cable paths and positioning may not represent the actual model. During the removal and replacement of components, ensure all available cable channels and clips are used and that the cables are replaced in the same position.
LCD Module Disassembly Flowchart
Remove LCD Panel from Main Unit before proceeding
Remove
LCD Bezel
Remove
LCD Panel
|
|
Remove |
|
Remove |
|
|
Remove |
|
|
|
LCD FPC Cable |
|
LCD Brackets |
|
|
Camera Module |
|
Screw List |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Step |
|
Screw |
|
Quantity |
|
|
Part No. |
|
|
|
|
|
|
|
|
|
|
LCD Bezel |
M2.5*5 |
6 |
|
86.ARE07.003 |
||||
|
|
|
|
|
|
|
|
|
LCD Panel |
M2.5*5 |
4 |
|
86.ARE07.003 |
||||
|
|
|
|
|
|
|
|
|
LCD Brackets |
M2*3 |
6 |
|
86.ARE07.002 |
||||
|
|
|
|
|
|
|
|
|
78 |
Chapter 3 |
Downloaded from www.Manualslib.com manuals search engine
Removing the LCD Bezel
1.See “Removing the LCD Module” on page 57.
2.Remove the six screw caps and screws from the LCD Bezel.
Step |
|
Size |
Quantity |
Screw Type |
|
|
|
|
|
LCD Bezel |
M2.5*5 |
|
6 |
|
|
|
|
|
|
3.Starting from the inside bottom edge, pry the Bezel away from the panel. Continue up the sides as shown. If necessary, use a plastic pry to release the corners of the Bezel.
Chapter 3 |
79 |
Downloaded from www.Manualslib.com manuals search engine
4.Lift up the Bezel and remove it from the LCD Module.
80 |
Chapter 3 |
Downloaded from www.Manualslib.com manuals search engine